BreatheAudio BA-LRC1 Checking The Codes, Sources a or B Changing Volume Lock, Programming Macros

6. If the device responds, go to step 6. If the device does not respond, press CH+. The remote will try the next code. Continue until the device responds.

NOTE: Press CH- to try the previous code.

7.To set the code, press SETUP once. The LED blinks twice.

8.To search for other device codes, repeat steps 1 to 6.

Checking The Codes

If you have set up the remote using the procedure in “Searching For Your Code”, you may need to find out which five-digit code is operating your equipment.

For example, to find out which code is assigned to your TV:

1.Press SOURCE A once.

2.Press and hold SETUP until the red LED blinks twice, then release.

3.Enter 990. The LED blinks twice.

4.To view the code for the first digit, press numeric key 1. Count the LED blinks (for example, three blinks = 3), and write down the number in the appropriate code listing in step 8 under “Programming a Device”.

NOTE: If a code digit is 0, the LED does not blink.

5.Repeat step 4 for the four remaining digits, using 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit.

6.To check for other device codes, repeat steps 1-5, substituting

Sources A or B.

Changing Volume Lock

The BA-LRC1 comes preset to allow independent volume control of each selected device (Global Volume Unlock). However, you may change the Volume Lock setting to Global Volume Lock so that one source’s volume will control volume in all other modes. After that, you can perform Individual Volume Unlock on a selected source to set its volume control for independent operation or Global Volume Unlock to remove all volume locking.

Locking Volume Control to One Mode (Global Volume Lock)

1.Press and hold SETUP until red LED blinks twice, then release.

2.Enter 993 and then press the mode key for the source you want to control volume (for example, CD). The LED blinks twice. Now, when you press VOL+, VOL- or Mute, the selected source (for example, CD) will control the volume regardless of the current mode.

Unlocking All Volume Control (Restoring Global Unlock)

1.Press and hold SETUP until the red LED blinks twice, then release.

2.Enter 993 and then press VOL+. The LED blinks four times. Volume is independently controlled for all programmed sources.

Unlocking a Single Source’s Volume Control

1.Press a source key (A or B).

2.Press and hold SETUP until the red LED blinks twice, then release.

3.Enter 993 and then press VOL-. The LED blinks four times. Volume is independently controlled for the selected sources.

Programming Macros

A macro can be used to control a home theater operation, to set a favorite channel, or for other multiple functions you would like to control with one key press. You can use any key to activate a macro. Moreover, each Macro Key can hold up to 32 key presses total.

You can program a macro that will operate regardless of what mode you are in, or one that will only operate when you are in a specific mode.

NOTE: Programming a new macro over an existing one will erase the original macro.

Programming a Mode-Independent Macro

1.Press and hold SETUP until the red LED blinks twice, then release.

2.Press 995. The LED blinks twice.

3.Press the key you want to use to activate your macro (POWER, any unused key, etc.).

4.Enter the series of commands you want the macro to execute (up to 32 commands).

5.Press and hold SETUP until the red LED blinks twice, then release.

Now, when you press the Macro key, the remote will send the series of commands you have entered, regardless of what mode you are in. For example, you could program the Macro key to turn on both your TV and cable box and select a particular channel.

To clear the macro, repeat steps 1 to 5 above, but do not enter a series of commands at step 4.

Programming a Mode-Dependent Macro

1.Press a source key (A or B).

2.Press and hold SETUP until the red LED blinks twice.

3.Press 978. The LED blinks twice.

4.Press the key you want to use to activate your macro (POWER, any unused key, etc.).

5.Enter the series of commands you want the macro to execute (up to 32 commands).

6.Press and hold SETUP until the red LED blinks twice, then release.

3