Harman-Kardon MAS 102, MAS 111 Operation, Using the Remote Control, Turning on the MAS System

MAS SYSTEM

Operation

Using the MAS system is simple and intuitive. The front-panel controls use advanced touch-sensitive technology. To use the front panel, place a finger over any of the illuminated icons. A gentle tap is all that is necessary. Wait a few seconds for the system to process each command. To remove fingerprints, wipe the front panel with a dry microfiber cloth.

Using the Remote Control

Point the remote at the front of the MAS system. The remote IR sensor is located on the right half of the front panel of the controller. Do not block the sensor. The remote has a range of approximately 6m, up to 30 degrees off center. If the batteries require replacement, see Step 2 of the Installation section. Use caution and dispose of batteries according to environmental requirements. Never throw the batteries into fire, and remove them from the remote if the remote will be unused for a long period of time.

Turning on the MAS System

To turn on the MAS system, press and hold the Power button on the remote or the controller for 1 second. The system will also turn on when one of the Source Selectors, the Eject button or the Play/Pause button on the remote is pressed.

Press the Power button to turn off the system. If the clock has been turned off, the message display will go dark to conserve power. Otherwise, the time will be displayed at half-brightness.

Setting the Clock

The clock may be set using the Settings menu. See Figure 2.

1.Press the Settings button on the remote.

2.Press the 7/3 buttons until “Time Setup” appears in the message display.

3.Press the Enter button to display “Clock.”

Turn the clock on or off: Press the Enter button and use the 7/3 buttons to select “On” or “Off.” Turning the clock off conserves power when the system is powered down to Standby mode.

4.Set the clock: Press the 7/3 buttons until “Set Clock” appears on the lower line. Press the Enter button to display “Set Time.”

tSet the time: Press the Enter button and use the numeric keys to enter the hour, then the minute. If the 12-hour time format is active, use the 7/3 buttons to select “AM” or “PM.” Press the Enter button to advance from one field to the next without changing it, and press the Enter or Back button to save the settings.

tSet the format: Press the 7/3 buttons until “Set 12/24 hour” appears. Press the Enter button to change the format, and use the 7/3 buttons to select between the 12- and 24-hour time displays. Press the Enter or Back button to save the change.

5.Set the day of the week: Press the 7/3 buttons until “Set Day” appears. Press the Enter button to display the day of the week, and use the 7/3 buttons to select the desired day. Press the Enter or Back button to save the changes.

Setting the Alarms

For automatic turn-on at a programmed time, set one or both of the alarms. The alarms may be set using the Settings menu. See Figure 3 on page 12.

1.Press the Settings button on the remote.

2.Press the 7/3 buttons until “Alarm Setup” appears in the message display.

Figure 2: Setting the Clock

				Ri ght
S e t t i n g s							S e t t i n g s
S p e a k e r S e t u p		>				< T i m e S e t u p			>
				Left
						Enter		Back
					Ri ght					Ri ght
		T i m e S e t u p		>		T i m e S e t u p			>
			C l o c k				S e t C l o c k
					Left					Left
	Enter			Enter or Back
						Enter			Back
			C l o c k	>
			O f f
										Ri ght
							S e t C l o c k		>
							S e t T i m e
										Left
						Enter			Enter or Back
							S e t T i m e		>
							1 2 : 4 3

T i m e S e t u p

<S e t D a y

Enter			Enter or Back
	S e t D a y		>
	M o n d a y
	S e t C l o c k
< S e t 1 2 / 2 4		h o u r >
Enter			Enter or Back
S e t 1 2 / 2 4		h o u r
	1 2 h o u r		>

11