Harman-Kardon AVR 645 owner manual Hdmi Output Connections, Scart A/V Connections

Page 18

Installation and Connections

•It is not possible to feed an analog composite or S-video signal to a recorder or the AVR’s multizone system when an HDMI input is in use. If an HDMI-equipped source also has analog audio and video outputs, connect them

to the Video 2 or Video 3 Video

and

Audio

on the AVR.

 

•In some instances, HDMI-equipped sources will not permit more than one video output at a time, and thus you cannot use the same source in the main listening room and with the recorder or remote zone at the same time. This is not a fault of the AVR, but rather a function of the content protection systems that are part of the HDMI standard.

HDMI Output Connections

Connect the HDMI Output to an HDMI input on your video display. Thanks to the AVR 645’s video processing system, all video input signals are converted to an HDMI output, so only one connection is required between the AVR and your display.

SCART A/V Connections

For the connections described above your video device needs RCA (cinch) connectors or/and S-Video connectors for all Audio and Video signals: Any normal video device (Not SVHS or High 8) for only playback needs 3 RCA jacks, VCRs for record and playback even 6 RCA jacks. Any S-Video device (SVHS, High 8) needs 2 RCA (Audio) and 1 S-Video jack (Video), if it´s a playback unit, or 4 RCA (Audio In/Out) and

2 S-Video (Video In/Out) jacks, if it´s a recording VCR.

Many european video devices are equipped with RCA (Cinch) or S-Video jacks only partially, not for all audio and video in/outputs needed as described above, but with a so called Scart or Euro-AV connector (almost rectangular jack with 21 pins, see drawings on next page).

In that case the following Scart to Cinch adapters or cables are needed:

•Units for playback, such as satellite receivers, camcorders, DVD or LD players, need an adapter from Scart to 3 RCA plugs, see fig. 1 (normal video devices) or from Scart to 2 RCA+1 S-Video plugs, see fig. 4 (S-Video devices).

•HiFi VCRs need an adapter from Scart to 6 RCA plugs, see fig. 2 (normal video), or from Scart to 4 Audio+2S-Video jacks, see fig. 5 (S-Video VCR). Read carefully the instruction attached to the adapter to find which of the six plugs is used for the record signal to the VCR (connect with the AVR´s Out jacks) and for the playback signal from the VCR (connect with the AVR´s In jacks). Do not misconnect Audio and Video signals. Don´t hesitate to consult your dealer, if you are uncertain.

•If you use only normal video devices the TV monitor needs an adapter from 3 RCA plugs to Scart (fig. 3) only. If also S-Video devices are used an adapter from 2 RCA+1S-Video plugs to Scart is needed additionally (fig. 6), connect- ed to the SCART input on your TV that is pro- vided for S-Video.

Note that only the video plugs (the "yellow" cinch plug in fig. 3 and the S-Video plug in fig. 6) must be connected to the TV Monitor Output , and the volume on the TV must be reduced to minimum.

Important Note for Adapter Cables:

If the cinch connectors of the adapter you’ll use are labeled, connect the Audio and Video ”In” plugs with the corresponding Audio and Video ”In” jacks on the AVR (and with a VCR connect the ”Out” plugs to the ”Out” jacks on the AVR). Note that with some adapter types it may be just turned around: If no signal is audible/ visible when the VCR is playing connect the “Out” plugs to the ”In” jacks on the AVR and turned around. If the adapter plugs are not labeled in that way, pay attention to the signal flow directions as shown in the diagrams above and in the instruc- tion attached to the adapter. If uncertain, don’t hesitate to consult your dealer.

18INSTALLATION AND CONNECTIONS

Page 17 Page 19
Image 18
Page 17 Page 19
Contents AVR 645 Audio/ Video Receiver Table of Contents Declaration of ConformityDescription and Features IntroductionIntroduction / Safety Information Important Safety InformationUnpacking Front Panel Controls To select between the Optical Coaxial ÓMore information Surround Back Right Tan Subwoofer LFE Rear Panel ConnectionsSurround Left Blue Surround Right Gray Surround Back Left Digital AudioDigital recorder such as a CD-R or MiniDisc recorder AC Power Cord Jack Connect the ACDigital Audio Outputs Connect these Monitor Component Video OutputsAVR 645 when appropriate upgrades are available + and negative terminalsRemote IR Carrier Output The output Main Remote Control Functions Light ButtonChannel Direct Inputs the input Movies Disc Skip Button This button has noMain Remote Control Functions Zone II Remote Control Functions Power Off B AVR Selector The Bridge /DMP Selector Media Player DMP Connector Optional is connected to DigitalAnalog Video Equipment Connections Installation and ConnectionsAudio Equipment Connections Output jacksVideo Inputs Hdmi ConnectionsHdmi Input Connections Connection NotesTo the Video 2 or Video 3 Video Audio Hdmi Output ConnectionsScart A/V Connections Important Note for Adapter CablesWith Scart that cannot be switched and pro- vided by the AVR Important Note for the Use SCART-Cinch AdaptersBUS Installation Connections System and Power ConnectionsMain Room Remote Control Extension Multiroom IR LinkSpeaker Selection Speaker PlacementAC Power Connections USB ConnectionsTo manually configure your surround back speaker Channel system for your main listening area seeSystem Setup System ConfigurationUsing the On-Screen Display First Turn OnIn/Out Setup C O U T A L O G Video Monitor Settings Audio SetupSurround Setup Surround Config then press the Set Button FQUsing EzSet/EQ Night Mode SettingsC K So that on is highlighted and press the Set Button F R F I E L D E QManual Setup Speaker Size MenuSpeaker Size LFE Low-Pass-Filter Setting SmallFollowing options are available Sub Mode SettingDelay Settings Subwoofer SizeOutput Level Adjustment Volume until you can hear the test noise clearly SetupAdditional Input Adjustments Surround Mode Chart OperationChannel Theater Channel presentation of two-channel stereo programsBasic Operation Source SelectionChannel/8-Channel Direct Input Surround Mode Selection Volume Up/Down ButtonsRepeatedly to scroll through the list of available modes Dolby Digital Digital Audio PlaybackUntil Surr OFF appears in the Main Information Display ˜ Rear panel Or front panel *ÓDigital Bitstream Indicators Selecting a Digital SourceUSB Playback Speaker/Channel Indicators Audio, while the main feature is availableNight Mode Front Panel In/Outputs UsingTape Recording Puts for Tape OutputsNormal output level adjustment for Output Level Adjustment With Source SignalsMemory Backup EzSet/EQ On/OffFront-Panel-Display Fade Advanced FeaturesTurn On Volume Level Display BrightnessSemi-OSD Settings Full-OSD Time Out AdjustmentDMP/ TheBridgeTMAuto Power Multiroom Operation Multiroom OperationIR Output Infrared Output SelectionMultiroom IR Input Full Carrier IR OutputTuner Operation Basic Tuner OperationRDS Operation Program Search PTY Up/Down button # until RDS only appears in the displayFor Configuring the RemotePreprogrammed Code Entry Button F appearsLearning Commands Automatic Code EntryLearning Codes for an Input Selector Device PriorityPress the ¤ Navigation Button E until Changing Devices Macro ProgrammingPower On VID 2/TV VID 3/Cable AVR Logic 7 O Erasing a MacroAt the next menu screen press Returning the Volume Control Settings to Default Operation Punch-Through ConfigurationVolume Punch-Through ButtonsTransport Punch-Through Returning the Channel Control Settings to Default OperationAt the next menu screen, press the ⁄¤ Navigation Buttons E untilRenaming ‹ /› Navigation Buttons E as requiredResetting the Remote At this point you have two optionsSee page 54 for more information Additional Notes on Configuring and Operating the Remote Backlight OptionsPower Switch 1 is pushed Troubleshooting GuideProcessor Reset Press the AVR Selector BSystem Defaults Video Input DefaultsSystem Default and Personal Settings Worksheets Worksheet B Surround Configuration Defaults and Settings Worksheet C Delay Defaults and SettingWorksheet D System Defaults and Settings Worksheet E Input Settings USBTechnical Specifications Harman Consumer Group, Inc

AVR 645 specifications

The Harman-Kardon AVR 645 is a standout receiver that appeals to audiophiles and home theater enthusiasts alike. This model is known for its rich sound quality, extensive features, and user-friendly interface, making it a solid choice for anyone looking to enhance their home entertainment experience.

At the heart of the AVR 645 is its robust amplification system. With a power output of 55 watts per channel at 8 ohms, the receiver provides ample power to drive a variety of speakers. The incorporation of Harman-Kardon's patented Logic 7 processing technology allows for an immersive surround sound experience, creating a sense of depth and realism in audio playback. This feature is particularly beneficial for film and gaming, as it helps to create a multidimensional soundstage that pulls viewers into the action.

The AVR 645 supports a variety of audio formats, including Dolby Digital, DTS, and Pro Logic II, ensuring compatibility with a wide range of media. The receiver is equipped with multiple audio inputs and outputs, including HDMI, optical, and coaxial connections, allowing users to easily connect their DVD players, gaming consoles, and other devices. Additionally, it features a built-in AM/FM tuner for those who enjoy traditional radio.

In terms of video capabilities, the AVR 645 is highly versatile, supporting both standard and high-definition video formats. The receiver includes multiple HDMI inputs, facilitating easy switching between different high-definition sources without compromising video quality. The ability to upconvert lower resolution video to near-HD quality further enhances the viewing experience, making it a great choice for those with diverse video content.

User-friendliness is another highlight of the AVR 645. The intuitive on-screen user interface makes it easy to navigate settings and setup configurations. The Zone II feature allows for audio playback in another room, expanding the potential for whole-home audio solutions.

Ultimately, with its blend of power, quality, and versatility, the Harman-Kardon AVR 645 remains a respected choice among home theater systems, ensuring an elevated audio and visual experience for all users.
Top Page Image Contents