Black & Decker FSMH1621S, FSMH16151 manual Accessories, Troubleshooting, Technical data

uWhen you have finished using the hand held steam cleaner, release the trigger switch (3), turn it ‘OFF’ and disconnect from the mains supply. Wait until the steam

mop cools down before storing. (approximately five minutes)

Caution! It is important to monitor the water level in the water tank. To refill the water tank and continue to sanitise/clean, turn the hand held steam cleaner ‘OFF’. Unplug the unit from the electrical wall outlet, refill the water tank (8).

Caution! Steam may continue to be produced for a short time after the trigger switch (3) is released, this is normal. Switch off and allow the unit to cool before removing any accessories.

Accessories

The performance of your appliance depends on the accessory used. BLACK+DECKER accessories are engineered to high quality standards and designed to enhance the performance of your appliance. By using these accessories you will get the very best from your appliance.

Technical data

		FSMH1621S	FSMH16151
		(Type 1)	(Type 1)
Voltage	Vac	230	230
Power	W	1600	1600
Tank capacity	ml	350	350
Weight	kg	3.6	3.6

Troubleshooting

If your appliance seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your local BLACK+DECKER repair agent.

Problem	Step	Possible solutions
The steam mop is	1	Check the unit is plugged in at the wall
not turning on.		socket.
	2	Check the unit is switched on using the on/
		off switch (1).
	3	Check the fuse in the plug.

(Original instructions)			ENGLISH
Problem	Step	Possible solutions
The digital controls	4	Check that the handle (10) of the steam mop
do not light up.		is pushed firmly into the steam mop body (9).
		Check that the arrow on the handle is flush
		with the top of the steam mop body (9).
	5	Check that the hand held steam cleaner (5)
		is firmly docked into the steam mop body (9).
	6	Check steps 1, then 2, then 3.
The steam mop is	7	The steam mop will only produce steam
not producing		once the handle is pulled back from the
steam.		upright position.
	8	Check that the water tank (8) is full.
		NOTE: When first filled or after running dry it
		can take up to 45 seconds for steam to be
		produced.
	9	Check that the Steam head (11) is firmly
		docked into the steam mop body (9).
	10	Check steps 5, then 1, then 2, then 3.
The digital controls	11	Check steps 4, then 5, then 1, then 2, then 3
go out during use.
The steam mop	12	Check steps 7, then 8, then 9, then 5, then 3.
stops producing
steam during use.
The steam mop is	13	The steam mop has 3 settings. Press the
producing too		autoselect button (6) to reduce the amount of
much steam during		steam being produced.
use.	14	Check that the steam burst button (25) has
		not been pressed.
The steam mop is	15	The steam mop has 3 settings. Press the
producing too little		autoselect button (6) to increase the amount
steam during use.		of steam being produced.
	16	Press the steam burst button (25) to
		temporarily increase the amount of steam.
No steam is being	17	The hand held steam cleaner has a lock off
produced from the		feature. Lift the lock off switch (2) and pull
hand held steam		the trigger switch (3). After a few seconds
cleaner when the		steam will be produced.
trigger is pulled.	18	Check steps 8, then 1, then 2, then 3.
The hand held	19	The hand held steam cleaner will begin to
steam cleaner is		produce steam after 15 seconds and will
producing too little		reach maximum steam flow after 45
steam during use.		seconds.
The hand held	20	Firmly press the hand held steam cleaner
steam cleaner will		release button (20) down, then pull the hand
not come out from		held steam (5) cleaner from the steam mop
the steam mop		body (9).
body.

9