Cartridge Change Determination, Pressure Gauges

Cartridge Change Determination

Replace the prefilter cartridge whenever it becomes excessively dirty (observed visually or by flow restriction). Follow the change instructions provided with the cartridge. Replace carbon filter cartridges when capacity is reached or when flow becomes inadequate, but at least annually. All carbon filter cartridges on multiple cartridge systems should be changed at the same time. Change the SS-10 cartridge when product level in the cartridge drops below 1/2" from the bottom of the bowl.

The system pressure gauge or optional Everguard™ Low Pressure Alarm (LPA) provides a quick, simple means of determining when the filter cartridge(s) should be checked. Installed on the system outlet manifold, the gauge or LPA can be used to monitor both dynamic (flowing) and static (line) pressure. The cartridge(s) should be changed when the pressure gauge is in the red area while equipment is in operation, and yet the needle shows adequate line pressure between cycles. Observe the needle during the next equipment on cycle. If the needle registers adequate pressure, it can be assumed that the temporary low-pressure condition was caused by a brief power failure or other incoming pressure disruption. If the low pressure condition is not due to an external condition, check/change the prefilter first. If the low pressure condition is still not corrected, change the carbon filter cartridges.

Pressure Gauges

Low Inlet	Adequate Inlet	Low Outlet	Adequate Outlet
Pressure	Pressure	Pressure	Pressure

Cartridge Change Procedure

E-Series Prefilter Cartridge Change

1.Shut off power to equipment. Shut off inlet water ahead of system.

Everpure Carbon Filter Cartridge Change

1.Shut off power to equipment. Shut off inlet water ahead of system.

2.Push red relief valve. Unscrew bowl. Remove prefilter cartridge.

2.Open flushing valve to relieve pressure.

3.Hold head firmly and push upward.

Turn cartridge to left until it stops.

3.Clean bowl with filtered water only; no special cleaners.

4.Feel head o-ring. If dry, lubricate with high quality silicone lubricant.

4.Pull cartridge downward and out of head.

5.Hold head firmly. Align cartridge lug with label. Insert new cartridge firmly into head.

5.Install new prefilter cartridge in bowl. Hand tighten bowl onto head.

6.Turn cartridge right 90˚ until rotation stops.

7.Repeat steps 3-6 for remaining cartridges.

6.Turn on water. Turn on power to equipment.

Flushing

8.With flushing valve fully open, open inlet water at full force for five minutes. Close flushing valve.

9.Turn on power to equipment

SR-X Feeder Cartridge Change

1.Shut off power to equipment. Shut off inlet water ahead of system.

2.Press red pressure relief button on head.

3.Unscrew bowl.

4.Remove old cartridge.

5.Feel bowl o-ring; if dry, lubricate with silicone lubricant.

6.Install new SS-10 cartridge into head.

7.Hand tighten bowl into head.

8.Turn on water.

9.Press red pressure relief button until water comes out of valve port.

10.Turn on power to equipment.

For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed plumber for installation of the system. This system and its installation must comply with state and local regulations.

EV3112, XC2, MC, XC specifications

Everpure's MC, XC2, EV3112, and XC filtration systems represent the pinnacle of water purification technology, combining robust engineering with advanced filtration capabilities. Designed for a variety of applications, these systems cater to businesses in the foodservice, hospitality, and coffee industries, ensuring that water quality meets the highest standards.

The MC series provides a versatile solution for foodservice operations, focusing on the removal of chlorine, sediment, and other impurities. It features a high-capacity filter designed to deliver consistent water quality, enhancing the flavor of beverages and the quality of food preparation. The innovative design ensures easy filter changes and maintenance, allowing businesses to minimize downtime.

The XC2 is particularly well-regarded for its dual filtration technology which targets both fine and coarse particles. This system is engineered to reduce scale buildup, which can be detrimental to equipment longevity. Furthermore, the XC2 integrates a unique activated carbon layer that not only enhances taste but also eliminates odors, presenting a comprehensive solution for establishments serving water and beverages.

Everpure's EV3112 brings a robust filtration approach with a focus on larger operations. Capable of delivering high volumes of filtered water, this system is equipped with a three-stage filtration process, ensuring maximum impurity removal. Its proprietary micro-filtration technology captures particulates down to 0.5 micron, offering high efficiency while also maintaining the essential minerals that enhance water taste.

Complementing these systems, the XC offers exceptional performance specifically geared towards espresso machines and coffee brewers. With fine filtration capabilities, it protects sensitive equipment from clogging and scale build-up while improving the extraction process for better-tasting coffee. The XC utilizes advanced carbon block technology, which is instrumental in retaining flavor while filtering out undesirable contaminants.

Collectively, these Everpure systems showcase the company’s commitment to quality, reliability, and innovation in water purification. Their cutting-edge technologies, along with user-friendly designs, make them an excellent choice for businesses that prioritize not only the quality of their water but also the efficiency and performance of their equipment. Whether for restaurants, cafes, or large-scale facilities, Everpure’s filtration solutions are engineered to meet the diverse needs of the food and beverage industry while ensuring that water quality remains consistently high.