See illustrations, High Flow CSR Twin | Everpure XC2, MC, EV3112

•Connect the outlet of the SR-X Feeder to the ice machine make-up water (not condenser water) line and coffee brewing equipment. Proceed to step 4.

3b. For High Flow CSR Quad Plus System, connect outlet to equipment served per the instructions be- low. Always use a NSF approved pipe dope or Teflon tape at all connections. Use a backup wrench on all fittings while connecting to avoid stress on the system components.

•Locate and mount the separate SR-X Feeder between the High Flow CSR system and the ice machine. Make-up water (not condenser water) line and coffee brewing equipment.

•A tee fitting is located in the system header before the surge tank isolation and flushing valve. Using minimum 1/2" I.D. line, connect the outlet of this tee to the fountain beverage and remote SR-X Feeder line. Important: Install a tee in this service water line to separate the fountain water feed from the ice machine/coffee brewer water feed.

In Massachusetts, a backflow preventer is required for this installation.

•Connect one branch of the service water tee to the fountain beverage equipment. Connect the other branch of the tee to the inlet of the SR-X Feeder. Connect the outlet of the SR-X Feeder to the ice machine make-up water (not condenser water) line and coffee brewing equipment.

•The surge tank isolation and flushing valve is located at the end of the system header. Using fittings and hose provided, connect one branch of the valve to the surge/storage tank. Connect a hose from the other (flushing) branch and run to drain. Note: Some municipal plumbing codes and good sanitary practices require an air gap at the drain termination point.

4.The surge/storage tank is pre-pressurized to 20 psi. Check pressure and adjust as necessary.

5.Install a manual shut-off valve leading to the system for servicing and connect minimum 1/2" I.D. (3/4" for quad) water line to the system inlet.

6.The optional Everguard™ Low Pressure Alarm (LPA) consists of a pressure switch, audible/visual alarm box and a power adapter. It is designed to detect a fixed low pressure (approx. 20 psi) condition as an indication of loss of system outlet pressure either due to an intentional shut-down or excess fouling of the water filters, thus indicating the need for filter cartridge change-out. If the system is equipped with the LPA, follow these steps:

•Determine location of a convenient 110 VAC outlet to plug in the LPA power adapter.

•Remove the protective rubber cap from the pressure switch installed in the system header assembly. Insert the wires from the LPA unit through the cap and connect them to the terminals on the pressure switch. Either wire can be connected to either terminal. Replace the cap.

•Plug the LPA power adapter into an outlet. The audible alarm should activate. Push the reset switch to silence.

•Unplug the LPA unit.

7.Shut off the system inlet valve located on the inlet of the prefilter head.

8.Check to be sure the o-ring on the prefilter housing is sufficiently lubricated. Use a good grade of silicone lubricant, if needed. Position the EC210 prefilter cartridge on guide seat in the bottom of the bowl. Then thread the bowl into the head by hand. Use a sump wrench to snug the bowl onto the head.

9.Install only genuine Everpure™ carbon filter cartridge(s) into the filter head(s) following directions on the cartridge label or as shown in the Cartridge Change illustrations. Install the SS-10 Scale Inhibitor cartridge into the SR-X housing.

10.Turn on inlet water to the filter system and check for leaks.

11.Open the flushing valve and flush the cartridge(s) by running water through at full force for five minutes. This will set the filtering media and purge any air and fines, insuring maximum filter life.

See illustrations.

12.After flushing, close the flushing valve, turn on power to equipment and plug the LPA (if so equipped) into the electrical outlet. The system is ready for operation.

FLUSHING

For maximum life, all carbon filter cartridges must be flushed for five minutes at full flow before use. ALL NEW CARTRIDGES MUST BE FLUSHED AFTER EACH CARTRIDGE CHANGE BEFORE BEING PUT INTO SERVICE!

If the cartridges are new, have been properly flushed and both needle and follower register inadequate pressure, or the LPA is sounding, you may be experiencing inadequate water pressure or some restriction may exist in the inlet water line. In either case, the incoming water pressure must be improved to receive optimum filter life.

COMPLETE CARTRIDGE CHANGE INSTRUCTIONS CAN BE FOUND ON THE FILTER CARTRIDGE LABEL.

Not for residential use. For food service applications only.

25.80"

FOUNTAIN OUTLET 3/4" FNPT

INLET

3/4" FNPTICE MACHINE/ COFFEE

OUTLET

3/4" FNPT

25.59"

Figure 5 – High Flow CSR Twin

30"

FOUNTAIN

OUTLET 3/4" FNPT

INLET	ICE MACHINE/
3/4" FNPT	COFFEE

OUTLET 3/4" FNPT

25.59"

Figure 6 – High Flow CSR Triple

34"

FOUNTAIN

OUTLET 3/4" FNPT

INLET	ICE MACHINE/
3/4" FNPT	COFFEE

OUTLET 3/4" FNPT

25.69"

Figure 7 – High Flow CSR Quad

31.38"

	ICE MACHINE/
INLET	COFFEE
3/4" FNPT	OUTLET
INSERT TEE FITTING.	3/4" FNPT
ONE OUTLET TO FOUNTAIN,
ONE OUTLET TO SRX.
OUTLET
3/4" FNPT

INLET 3/4" FNPT

29.69"

Figure 8 – High Flow CSR Quad Plus

Check for compliance with state and local laws and regulations. The Commonwealth of Massachusetts Plumbing Code 248CMR shall be adhered to. Consult your local licensed plumber for installation of this system. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

EV3112, XC2, MC, XC specifications

Everpure's MC, XC2, EV3112, and XC filtration systems represent the pinnacle of water purification technology, combining robust engineering with advanced filtration capabilities. Designed for a variety of applications, these systems cater to businesses in the foodservice, hospitality, and coffee industries, ensuring that water quality meets the highest standards.

The MC series provides a versatile solution for foodservice operations, focusing on the removal of chlorine, sediment, and other impurities. It features a high-capacity filter designed to deliver consistent water quality, enhancing the flavor of beverages and the quality of food preparation. The innovative design ensures easy filter changes and maintenance, allowing businesses to minimize downtime.

The XC2 is particularly well-regarded for its dual filtration technology which targets both fine and coarse particles. This system is engineered to reduce scale buildup, which can be detrimental to equipment longevity. Furthermore, the XC2 integrates a unique activated carbon layer that not only enhances taste but also eliminates odors, presenting a comprehensive solution for establishments serving water and beverages.

Everpure's EV3112 brings a robust filtration approach with a focus on larger operations. Capable of delivering high volumes of filtered water, this system is equipped with a three-stage filtration process, ensuring maximum impurity removal. Its proprietary micro-filtration technology captures particulates down to 0.5 micron, offering high efficiency while also maintaining the essential minerals that enhance water taste.

Complementing these systems, the XC offers exceptional performance specifically geared towards espresso machines and coffee brewers. With fine filtration capabilities, it protects sensitive equipment from clogging and scale build-up while improving the extraction process for better-tasting coffee. The XC utilizes advanced carbon block technology, which is instrumental in retaining flavor while filtering out undesirable contaminants.

Collectively, these Everpure systems showcase the company’s commitment to quality, reliability, and innovation in water purification. Their cutting-edge technologies, along with user-friendly designs, make them an excellent choice for businesses that prioritize not only the quality of their water but also the efficiency and performance of their equipment. Whether for restaurants, cafes, or large-scale facilities, Everpure’s filtration solutions are engineered to meet the diverse needs of the food and beverage industry while ensuring that water quality remains consistently high.