System Configuration
default setting of GLOBAL will be appropriate, as most listeners do not need to have individualized speaker settings. However, some listeners, particularly those with full-range front speakers that are used for both movies and music may prefer that different speaker settings be used when listening to music through a CD player as opposed to a movie from a DVD player, VCR or cable/satellite set top.
If you wish to customize the speaker size individ- ually to each input, make certain that the cursor is on the BASS MGR line and press the ‹/› Buttons E so that INDEPENDENT appears in highlighted video. When this setting is entered all speaker size settings will be shown with their factory default size in the menu and all other inputs will turn to INDEPENDENT too. Now you should enter the speaker size settings preferred for the input selected, as described below. Remember that in this case the size settings just entered will apply to the current input ONLY, and you will need to go back to the INPUT menu to select another input, and then return to this menu page again to change the settings for the next input. Repeat the procedure for any input where you wish to have a set of speaker configuration different from the default settings.
NOTE: When the INDEPENDENT setting is activated, you may assign different speaker size settings to each input to accommodate different bass management settings that match your preferences with the type of program material normally used with a particular source (for example, when movies are played from DVD and music from a CD player). However, the actual speaker crossover settings are set only once and do not change with the input selection. The reason is that, while bass management preferences may vary, the actual speakers remain the same, regardless of the bass-management and redirection settings.
2.Begin the speaker size setup process by making certain that the cursor is pointing toward the LEFT/RIGHT line, which sets the configura- tion for the front left and right speakers. If you wish to make a change to the front speakers’
configuration, press the ‹ / › Buttons E so that either LARGE or SMALL appears, match- ing the appropriate description from the definitions shown above.
When SMALL is selected, low-frequency front channel sounds will be sent only to the subwoofer output. If you choose this option and there is no subwoofer connected, you will not hear any low- frequency sounds with front channel signals.
When LARGE is selected, a full-range output will be sent to the front left and front right outputs. Depending on the choice made in the SUBWOOFER line in this menu (see below), the
front left and right bass information may also be directed to the subwoofer.
NOTE: When the front speakers are set to the LARGE option and the surround mode is set to "Surround Off", or pure two-channel stereo, when an analog signal source is present it will be routed directly from the input to the volume control without being digitized or processed. If you have full-range front speakers and wish to remove all digital processing from the circuit path, select this configuration. If you wish to set this option for use with only one input, such as a CD player that uses an external DAC or an optional, external phono preamp, you must choose the INDEPENDENT setting on the BASS MGR line at the bottom of this menu so that only those inputs where the analog bypass is desired will be routed in this fashion, while other analog inputs such as a VCR or cable box will be digitized for surround processing.
Important Note: When a speaker set with a subwoofer and two front satellites connected to the Sub´s speaker outputs is used, the Sub´s inputs must be connected to the Front speaker outputs and LARGE must be selected for the front speakers (and NONE for the subwoofer, see below).
3.When you have completed your selection for the front channel, press the ¤ Button D on the remote to move the cursor to CENTER.
4. Press the ‹/› Buttons E on the remote to select the option that best describes your center speaker, based on the speaker definitions shown below.
When SMALL is selected, low-frequency center channel sounds will be sent to the Fronts, if they are set to LARGE and Sub is turned off (see be- low). When Sub is on, low frequency center channel sounds will be sent to the subwoofer only.
When LARGE is selected, a full-range output will be sent to the center speaker output, and NO center channel signal will be sent to the sub- woofer output (except when the Pro Logic II Music mode is in use).
NOTE: If you choose Logic 7 as the surround mode for the particular input source for which you are configuring your speakers, the AVR will not make the LARGE option available for the center speaker. This is due to the requirements of Logic 7 processing, and does not indicate a problem with your receiver.
When NONE is selected, no signals will be sent to the center-channel output. The receiver will operate in a “phantom” center channel mode. Center-channel information will be sent to the left and right front channel outputs and the cen- ter channel bass will be sent to the subwoofer output when L/R+LFE is selected in the
SUBWOOFER line in this menu (see below). This mode is needed if no Center speaker is used. Note that when the Logic 7 Cinema or Enhanced surround modes are selected a Center speaker must be used, the Logic 7 Music mode works well without a Center too.
5.When you have completed your selection for the center channel, press the ¤ Button D on the remote to move the cursor to
SURROUND.
6. Press the ‹/› Buttons E on the remote to select the option that best describes the sur- round speakers in your system based on the speak- er definitions shown on page 23.
When SMALL is selected, with all digital sur- round modes low-frequency surround channel sounds will be sent to the Fronts when Sub is turned off or to the subwoofer output when Sub is on. With any analog surround mode the rear bass feed depends on the mode selected and the setting of the Sub and front speakers.
When LARGE is selected, a full-range output will be sent to the surround channel outputs (with all analog and digital surround modes), and except with Hall and Theater modes, NO surround channel bass will be sent to the subwoofer out- put.
When NONE is selected, surround-sound infor- mation will be split between the front left and front right outputs. For optimal performance when no surround speakers are in use, the Dolby 3 Stereo mode should be used.
7.When you have completed your selection for the surround channels, press the ¤ Button D on the remote to move the cursor to
SUBWOOFER.
8. Press the ‹/› Buttons E on the remote to select the option that best describes your system.
The choices available for the subwoofer position will depend on the settings for the other speak- ers, particularly the front left/right positions.
If the front left/right speakers are set to SMALL, the subwoofer will automatically be set to SUB, which is the “on” position.
If the front left/right speakers are set to LARGE, three options are available:
• If no subwoofer is connected to the AVR, press the ‹/› Buttons E on the remote so that NONE appears in the on-screen menu. When this option is selected, all bass informa- tion will be routed to the front left/right “main” speakers.
•If a subwoofer is connected to the AVR, you have the option to have the front left/right “main” speakers reproduce bass frequencies at all times, and have the subwoofer operate only
