Harman-Kardon AVR 155 owner manual Front Panel Controls

Front Panel Controls

ENGLISH

1 Volume Control	! Tuner Band Selector	Ô Video 3 input jacks
2 System Power Control	@ OK Button	 Digital Input Selector
3 Power Indicator	# Preset Stations Selector	Ò Main Information Display
4 Headphone Jack	$ Speaker/Channel Input Indicator	Ú Remote Sensor Window
5 Surround Mode Group Selector	% Input Source Selector
6 Speaker Select Button	^ RDS Select Button
7 Selector Buttons	& Delay
8 Tone Mode	* Digital Optical 3 Input
9 Surround Mode Selector	( Channel Select Button
) Tuning Up/Down	Ó Digital Coax 3 Input
1 Volume Control: Turn this knob clockwise	converts the small mini-plug at the end of the	8 Tone Mode: Pressing this button enables or
to increase the volume, counterclockwise to	microphone’s cord to a 1/4" plug.	disables the Balance, Bass and Treble tone
decrease the volume. If the AVR is muted, adjust-	5 Surround Mode Group Selector: Press this	controls. When the button is pressed so that the
ing volume control will automatically release the		words TONE IN appear in the Main
	button to select the top-level group of surround
unit from the silenced condition.		Information Display Ò, the settings of the
	modes. Each press of the button will select a
		Bass and Treble controls and of the Balance
2 System Power Control: When the Main	major mode grouping in the following order:
		control will affect the output signals.
Power Switch ￿ on the rear panel is “ON,”	Dolby Modes ‹ DTS Digital Modes ‹ DSP Modes
		If you press 8 until TONE IN or TONE OUT
press this button to turn on the AVR; press it	‹ Stereo Modes ‹ Logic 7 Modes
		appear in the Display, you can switch between
again to turn the unit off (to Standby). Note that
	Once the button is pressed so that the name of	these two functions with the Selector Buttons 7
the Power Indicator 3 will turn white when
		the words TONE OUT appear in the Main
	the desired surround mode group appears in the
the unit is on.
		Information Display Ò, the output signal will
	Main Information Display Ò, press the
3 Power Indicator: This LED will be illuminated		be “flat,” without any balance, bass or treble
	Surround Mode Selector 9 to cycle through
in amber when the unit is in the Standby mode	the individual modes available. For example, press	alteration.
to signal that the unit is ready to be turned on.	this button to select Dolby modes, and then press	9 Surround Mode Selector: Press this button
When the unit is in operation, the indicator will	the Surround Mode Selector 9 to choose
		to select from among the available surround
turn white.	from the various mode options.
		mode options for the mode group selected. The
4 Headphone Jack: This jack may be used to	6 Speaker Select Button: Press this button	specific modes will vary based on the number of
listen to the AVR’s output through a pair of head-	to begin the process of selecting the speaker	speakers available, the mode group and if the
phones. Be certain that the headphones have a	positions that are used in your listening room.	input source is digital or analog. For example,
standard 6.3 mm stereo phone plug. Note that	(See page 17 for more information on setup and	press the Surround Mode Group Selector 5
the speakers will automatically be turned off	configuration.)	to select a mode grouping such as Dolby or
when the headphones are connected.	7 Selector Buttons: When you are establishing	Logic 7, and then press this button to see the
When configuring your system using EzSet/EQ,		mode choices available. For more information on
	the AVR’s configuration settings, use these buttons
		mode selection, see page 30.
the calibration microphone should be plugged	to select from the choices available, as shown in
into this jack 4 using the supplied adaptor that	the Main Information Display Ò.
		FRONT PANEL CONTROLS 5