Harman-Kardon AVR 1650 Step Two Measure the Speaker Distances, Step Three Manual Setup Menu

Page 22

AVR 1650/AVR 165

Advanced Functions, continued

Step Two – Measure the Speaker Distances

Ideally, all of your speakers would be placed in a circle, with the listening position at the center. However, you may have had to place some speakers a little farther away from the listening position than others. Sounds that are supposed to arrive simultaneously from different speakers may blur, due to different arrival times.

Your AVR provides a Distance adjustment that compensates for these real-world speaker-placement differences.

Measure the distance from each speaker to the listening position, and write it down in Table A4 in the Appendix. Even if all of your speakers are the same distance from the listening position, enter your speaker distances as described in Set the Speaker Distances, on this page.

Step Three – Manual Setup Menu

Now you are ready to program the AVR. Sit in your usual listening position, and make the room as quiet as possible.

With the AVR and video display turned on, press the OSD button to display the menu system and select Manual Setup. The Manual Setup menu will appear:

* MANUAL SETUP *

NUMBER OF SPEAKERS

SUB MODE : SUB

CROSSOVER

DISTANCE

LEVEL ADJUST

BACK TO MASTER MENU

NOTE: All of the speaker setup submenus include a “Back to…” option. To save the current settings, select the Back to… option.

For best results, adjust the submenus in this order: Number of Speakers, Crossover, Sub Mode, Distance and Level Adjust.

Number of Speakers

This selection lets you program the correct setting for each speaker group. The settings in this menu affect the remainder of the speaker-setup process and the availability of various surround modes at any time.

Select ON when the speakers are present in the system; select OFF for positions where no speakers are installed. The Front Left & Right setting is always ON and may not be disabled.

* NUMBER OF SPEAKERS *

LEFT/RIGHT

: ON

CENTER

: ON

SURROUND

: ON

SUBWOOFER

: ON

BACK TO MANUAL SETUP

When you have finished, select Back to Manual Setup.

Crossover (Size)

After you return to the Manual Setup menu, navigate to the Crossover line and press the OK button to display the Crossover menu.

* CROSSOVER *

LEFT/RIGHT

: 100Hz

CENTER

: 100Hz

SURROUND

: 100Hz

SUBWOOFER

: 10inch

BACK TO MANUAL SETUP

Refer to Table A6 for each speaker’s crossover frequency.

NOTE: The AVR will let you adjust settings only for those speaker groups you set to On in the Number of Speakers menu.

For each speaker group, select one of these eight crossover frequencies: LARGE, 40Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz or 200Hz. If the speaker’s crossover frequency is below 40Hz, select the first option, LARGE. This setting doesn’t refer to the speaker’s physical size but to its frequency response, which is also called “full range.”

Specify the size of the subwoofer’s transducer as 8, 10, 12 or 15 inches. The AVR always sets the subwoofer crossover to 100Hz but uses the transducer size for equalization.

Write down the settings in Table A6 in the Appendix.

When you have finished entering the settings, select Back To Manual Setup.

Sub Mode

After you return to the Manual Setup menu, navigate to the Sub Mode line and press the OK button to display the Sub Mode menu. This setting depends upon the Crossover setting you selected for the front left and right speakers.

If you set the front speakers to a numeric crossover frequency, the subwoofer setting will always be SUB. All low-frequency information will always be sent to the subwoofer. If you don’t have a subwoofer, either upgrade to full-range front left and right speakers or add a subwoofer at the earliest opportunity.

If you set the front speakers to LARGE, select one of the three following settings for the subwoofer:

L/R+LFE: This setting sends all low-frequency information to the subwoofer, including

a)information that would normally be played through the front left and right speakers and b) the special low-frequency effects (LFE) channel information.

OFF: Select this setting when no subwoofer is in use. All low-frequency information will be sent to the front left and right speakers.

LFE: This setting plays low-frequency information contained in the left and right program channels through the front left and right speakers, and directs only the LFE- channel information to the subwoofer.

When you have finished entering the settings, select Back To Manual Setup.

Set the Speaker Distances

As described above in Step Two, when you measured the distances from each of your speakers to the listening position, your AVR provides an adjustment that compensates for the different distances so that the sound from each speaker will reach the listening position at the proper time. This process will improve the clarity and detail of the sound.

After you return to the Manual Setup menu, navigate to the Distance line and press the OK button to display the Distance menu.

 

* DISTANCE *

FL

: 10FT

SL : 10FT

CEN

: 10FT

SUB : 10FT

FR

: 10FT

 

SR

: 10FT

 

DELAY RESET : OFF

UNIT : FEET

A/V SYNC DELAY : 0mS

BACK TO MANUAL SETUP

Enter the distance from each speaker to the listening position that you measured in Step Two and recorded in Table A4 in the Appendix (see page 28). Select a speaker, then use the Left/Right buttons to change the measurement. You can enter distances between 0 and 30 feet (9.1m). The default distance for all speakers is 10 feet (3m).

The default unit of measurement is feet. To change the unit to meters, scroll down to the Unit line and press the Left/Right buttons.

When you have finished entering the settings, select Back To Manual Setup.

22

Image 22
Contents AVR 1650/AVR Table of Contents Introduction Supplied AccessoriesPlace the AVR Front-Panel Controls PowerFront-Panel Controls ButtonAVR 1650/AVR Rear-Panel Connectors Rear-Panel ConnectorsAVR 1650/AVR 165 Rear-Panel Connections AVR 1650 shown Rear-Panel Connectors System Remote Control Functions System Remote Control FunctionsSystem Remote Control Functions Introduction to Home Theater Subwoofer Connections Types of Home Theater System ConnectionsSpeaker Connections Source Device ConnectionsVideo Connections Radio ConnectionsUSB Port Making Connections Making ConnectionsComposite video devices Hdmi devicesComponent video devices Optical digital audio devicesConnect The Bridge Iiip Connect the Radio AntennasConnect IR Equipment Audio recordersInstall the Batteries in the Remote Control Set Up the Remote ControlConnect to AC Power Connect the 12V Trigger OutputUsing the On-Screen Menu System Set Up the AVRSet Up the AVR Configure the AVR for Your SpeakersPress the OK button when you have finished Assign the Digital Audio ConnectorsAdditional Input Setup Menu Items Use the remote’s down arrow button to select AudioOperating Your AVR Operating Your AVRAdvanced Functions Selecting a Surround ModeAudio Processing and Surround Sound Advanced Functions Manual Speaker SetupDolby Pro Logic II Music Mode Adjustments Step One Determine Your Speakers’ Crossover FrequenciesStep Two Measure the Speaker Distances Step Three Manual Setup MenuSub Mode Number of SpeakersSystem Setup Step Four Setting Channel Output Levels ManuallyResetting the Remote Advanced Remote Control ProgrammingSleep Timer Processor ResetTroubleshooting TroubleshootingSymptom Cause Solution Specifications SpecificationsAppendix Appendix Default settings, worksheets, remote product codesTable A2 Source Setting Defaults Table A1 Recommended Source Component ConnectionsSub Mode Table A3 Speaker/Channel Setting DefaultsTable A4 Distance Settings Source All SourcesVideo Aux Tape Tuner Bridge Table A5 Source SettingsTable A6 Speaker/Channel Settings Front Left Front Right Center Surround Left Surround RightSource Input Product Type circle one Remote Control Code Table A7 Remote Control CodesTable A8 System Settings Feature Default Setting Your SettingSurround Mode Description Incoming Bitstream or Signal Table A9 Surround Modes2/.0 or Mode GroupDTS Digital DTS-ES Matrix played asAVR 1650/AVR Table A10 Remote Control Function List 3/4Rewind WW Table A11 Remote Control Product Codes TV Setup Code NumberTable A12 Remote Control Product Codes VCR Table A13 Remote Control Product Codes CD Table A14 Remote Control Product Codes DVD Table A15 Remote Control Product Codes SATCassette Deck Setup Code Number Manufacturer/Brand Table A16 Remote Control Product Codes TapeTable A17 Remote Control Product Codes Cable 001111 112 013 019 020 085001 041 119 171 209 215 116