Brother EX 660 operation manual For models equipped with the fast bobbin winding system

Page 15

NCBC2000.book Page 13 Thursday, October 21, 2004 4:32 PM

■For models equipped with the fast bobbin winding system

aFollow steps 1 through 2 of the procedure in “Winding the bobbin” to pass the thread around the pre-tension disk (page 11).

bPlace the bobbin on the bobbin winder shaft so that the spring on the shaft fits into the notch in the bobbin.

aNotch

bBobbin winder shaft spring

cSlide the bobbin winder shaft to the right.

dWhile holding the thread that wraps around the pre-tension disk with your left hand, use your right hand to wind the free end of the thread clockwise around the bobbin five or six times.

ePull the thread to the right and pass it through the slit in the bobbin winder seat.

aSlit in bobbin winder seat (with built-in cutter)

X The thread is cut to a suitable length.

CAUTION

●Be sure to cut the thread as described. If the bobbin is wound without cutting the thread using the cutter built into the slit in the bobbin winder seat, the thread may become tangled in the bobbin or the needle may bend or break when the bobbin thread starts to run out.

fSlide the sewing speed controller to the right (to set the speed to fast) (for models equipped with the sewing speed controller).

1

aSewing speed controller

gTurn on the sewing machine.

hPress the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to start.

Note

●If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on the machine.

●When the foot controller is plugged in, the start/stop button cannot be used to start or stop sewing (only for models equipped with the start/stop button).

iWhen the bobbin begins spinning slowly, take your foot off the foot controller or press (start/stop button) (for models equipped with the start/stop button).

jCut the thread, slide the bobbin winder shaft to the left and remove the bobbin.

kSlide the sewing speed controller back to its original position (for models equipped with the sewing speed controller).

CAUTION

●Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.

12

aWound evenly

bWound poorly

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Computerized Sewing Machine Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only For safe operation For a longer service lifeContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsNeedle and presser foot section Operation buttonsButtons provided on some models Operation panel Flat bed attachmentASlideopen theit. flat bed attachment to the left to Optional accessories AccessoriesCTo turn off the machine, set the main power switch to Using Your Sewing MachinePower supply precautions BSet the main power switch toChanging the needle stop position Foot controllerThreading the Machine Winding the bobbinETurn on the sewing machine GTrim the excess thread above the bobbin CSlide the bobbin winder shaft to the right For models equipped with the fast bobbin winding systemLower threading Tension-adjusting springFor models equipped with the quick-set bobbin Right side see arrow b until the cover clicks into placeUpper threading Thread take-up lever ECatch the thread on the hook as shown below Fully lower the needle threader leverGthe needle toward the back of the sewing MachineDrawing up the lower thread For models equipped with the quick-set bobbinALightly hold the end of the upper thread Fabrics Needle precautionsReplacing the Needle Needle types and their usesIncorrect needle Checking the needleReplacing the needle Correct needleInstalling the needle clamp Twin needle threading Sewing with a twin needleReplacing the Presser Foot Replacing the presser footMark on the wheel points up. With models ARemove the presser foot Removing the presser foot holderRemoving the presser foot holder Attaching the presser foot holderSewing General sewing procedureCAttach the presser foot DIfwidth.necessary, adjust the stitch lengthSelecting stitching ATurn on the sewing machineStarting to sew On the wheel points up. With models equippedBRaise the presser foot lever Upper tension is too tight Thread tensionSewing reinforcement stitches Correct tensionSewing curves Useful Sewing TipsTrial sewing Changing the sewing directionASlidereleasetheit.flat bed attachment to the left to Using a free-arm styleSewing thin fabrics Sewing stretch fabricsAttach overcasting foot G or zigzag foot J Select a stitch Overcasting StitchesChanging the needle position FWhen sewing is finished, cut the threadBasic Stitching Basic stitchingBlind HEM Stitching BAttach blind hem foot R CSelect a stitchIf the needle does not catch the hem fold Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingIf the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as Button sewing Sewing buttonholes on stretch fabricsCAttach presser foot M With stitch Select stitch ESelect a stitchRev. Reverse Zipper InsertionSewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingFor a seam allowance on the left side PiecingPatchwork crazy quilt stitching DCarefully sew around the edge of the designQuilting Using the optional quilting guideFree-motion quilting ARemoveholder. the presser foot and the presser footGAfter sewing is finished, slide the feed dog AAttach zigzag foot J BSelect stitch CStart sewing Reinforcement StitchingTriple stretch stitching Bar tack stitchingEPullpossible.down the buttonhole lever as far as 16-1/4 16-3/16 Loom stitching, etc Decorative StitchingFabric.3 FagotingScallop stitching AAttach monogramming foot N BSelect stitchDPull the bobbin threads to create gathers SmockingShell tuck stitching CSew parallel stitching at intervals of 1 cm 3/8 inchHeirloom stitching JoiningUtility stitches Stitch SettingsRfc. Reinforcement Pattern No Attaching appliqués 5.0 4.0 Rfc Appendix Maintenance Cleaning the machine surfaceCleaning the bobbin case ERemove the bobbin case Troubleshooting Fabric is LowerOr breaks Thread tenPitched noise While sewing Stitches areSkipped There is a highOperation beep for models equipped with the operation beep Error MessagesNumerics Index30 , 32 2000cover2-3.fm Page 2 Monday, October 4, 2004 402 PM

EX 660 specifications

The Brother EX 660 is a versatile and user-friendly embroidery machine that has garnered attention for its range of features tailored to both beginners and experienced crafters. This innovative machine combines advanced technology with user-centric design to deliver exceptional performance in embroidery tasks.

One of the standout features of the Brother EX 660 is its expansive embroidery area. With a generous embroidery field, users can create large and intricate designs without the need for constant repositioning of the fabric. This feature is particularly useful for quilting enthusiasts who want to incorporate detailed motifs into their projects.

Equipped with a variety of built-in designs and fonts, the Brother EX 660 empowers users to unleash their creativity. The machine houses hundreds of pre-installed embroidery designs, ranging from floral patterns to seasonal themes. Additionally, it offers a selection of fonts for monogramming, allowing users to personalize their creations effortlessly.

The Brother EX 660 also utilizes cutting-edge technology that simplifies the embroidery process. The machine features an easy-to-use LCD touchscreen display, which enables users to navigate through options and settings with ease. This user-friendly interface streamlines the process of selecting designs, adjusting settings, and monitoring progress.

Another significant characteristic of the Brother EX 660 is its compatibility with USB flash drives. This feature allows users to import custom designs from their computers or the internet, providing endless possibilities for creativity. Whether it's a unique personal design or a specific pattern found online, the machine can accommodate various file formats for added convenience.

In terms of ease of use, the Brother EX 660 boasts an automatic needle threader that saves time and minimizes frustration. This feature ensures a smooth and hassle-free start to any embroidery project. Additionally, the machine’s drop-in bobbin system is designed for quick and easy bobbin changes, enhancing overall efficiency.

The Brother EX 660 is also built with durability in mind. Its robust construction and high-quality materials ensure that the machine can withstand intensive use while delivering reliable performance. This makes it a great investment for anyone passionate about embroidery and sewing.

In conclusion, the Brother EX 660 emerges as an exemplary tool for embroidery enthusiasts. With its spacious embroidery area, extensive built-in designs, user-friendly technology, USB compatibility, and durable design, it stands out as a top choice. Whether you are a novice or an experienced embroiderer, this machine promises to enhance your crafting experience and inspire your creativity.
Top Page Image Contents