Brother EX 660 Error Messages, Operation beep for models equipped with the operation beep

Page 64

NCBC2000.book Page 62 Thursday, October 21, 2004 4:32 PM

APPENDIX

——————————————————————————————————————————————————————————

ERROR MESSAGES

If an operation is performed incorrectly before the sewing machine is set up, an error message appears on the operation panel. Follow the instructions indicated in the table.

If you press the stitch selection key or do the operation correctly while the error message is displayed, the message disappears.

Error Message

Probable Cause

Solution

 

 

 

 

The foot controller was pressed (or the start/stop but-

Lower the presser foot lever

 

ton was pressed if the foot controller is not con-

 

before continuing the opera-

 

nected) and the reverse/reinforcement stitch button

 

tion.

 

was pressed while the presser foot is raised.

 

 

 

 

 

 

A stitch other than the buttonhole or bar tack stitch

 

 

was selected and the foot controller was pressed (or

Raise the buttonhole lever

 

the start/stop button was pressed if the foot controller

before continuing the opera-

 

is not connected) while the buttonhole lever is low-

tion.

 

ered.

 

 

 

 

 

The buttonhole or bar tack stitch was selected and

Lower the buttonhole lever

 

the foot controller was pressed (or the start/stop but-

 

before continuing the opera-

 

ton was pressed if the foot controller is not con-

 

tion.

 

nected) while the buttonhole lever is raised.

 

 

 

 

 

 

The reverse/reinforcement stitch button or needle

Move the bobbin winder

 

position button was pressed while the bobbin winder

shaft to the left before con-

 

shaft is moved to the right.

tinuing the operation.

 

 

 

 

 

Disconnect the foot control-

 

The start/stop button was pressed while the foot con-

ler, and then press the start/

 

troller was connected.

stop button. Otherwise,

 

operate the machine by

 

 

 

 

using the foot controller.

 

 

 

 

 

Remove the tangled thread

 

The motor locked up because the thread is tangled.

before continuing the opera-

 

 

tion.

 

 

 

Note

If error message “F1” through “F8” appears in the LCD while the sewing machine is being used, the machine may be malfunctioning. Contact your nearest authorized service center.

Operation beep (for models equipped with the operation beep)

Each time a key is pressed you will hear one beep. If a non-functioning key is pressed or an incorrect operation is performed you will hear two or four beeps (only for models equipped with the operation beep).

If a key is pressed (correct operation) One beep sounds.

If an incorrect operation is performed or a non-functioning key is pressed Two or four beeps sound.

If the machine locks up, for example, because the thread is tangled

The sewing machine beeps for four seconds and the machine automatically stops. Be sure to check for the cause of the error, and correct it before continuing to sew.

62

Image 64
Contents Computerized Sewing Machine Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsOperation buttons Needle and presser foot sectionButtons provided on some models Flat bed attachment Operation panelASlideopen theit. flat bed attachment to the left to Accessories Optional accessoriesUsing Your Sewing Machine Power supply precautionsBSet the main power switch to CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionWinding the bobbin Threading the MachineETurn on the sewing machine GTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightTension-adjusting spring Lower threadingRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever Fully lower the needle threader lever Gthe needle toward the back of the sewingMachine ECatch the thread on the hook as shown belowFor models equipped with the quick-set bobbin Drawing up the lower threadALightly hold the end of the upper thread Needle precautions Replacing the NeedleNeedle types and their uses FabricsChecking the needle Replacing the needleCorrect needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingReplacing the presser foot Replacing the Presser FootMark on the wheel points up. With models Removing the presser foot holder Removing the presser foot holderAttaching the presser foot holder ARemove the presser footGeneral sewing procedure SewingDIfwidth.necessary, adjust the stitch length Selecting stitchingATurn on the sewing machine CAttach the presser footOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Thread tension Sewing reinforcement stitchesCorrect tension Upper tension is too tightUseful Sewing Tips Trial sewingChanging the sewing direction Sewing curvesUsing a free-arm style Sewing thin fabricsSewing stretch fabrics ASlidereleasetheit.flat bed attachment to the left toOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchFWhen sewing is finished, cut the thread Basic StitchingBasic stitching Changing the needle positionBAttach blind hem foot R CSelect a stitch Blind HEM StitchingIf the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as Sewing buttonholes on stretch fabrics Button sewingCAttach presser foot M ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseStretch stitching Sewing Stretch Fabrics and Elastic TapeElastic attaching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPiecing Patchwork crazy quilt stitchingDCarefully sew around the edge of the design For a seam allowance on the left sideUsing the optional quilting guide QuiltingARemoveholder. the presser foot and the presser foot Free-motion quiltingGAfter sewing is finished, slide the feed dog Reinforcement Stitching Triple stretch stitchingBar tack stitching AAttach zigzag foot J BSelect stitch CStart sewingEPullpossible.down the buttonhole lever as far as Decorative Stitching 16-1/4 16-3/16 Loom stitching, etcFagoting Scallop stitchingAAttach monogramming foot N BSelect stitch Fabric.3Smocking Shell tuck stitchingCSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersJoining Heirloom stitchingStitch Settings Utility stitchesRfc. Reinforcement Pattern No Attaching appliqués 5.0 4.0 Rfc Appendix Cleaning the machine surface MaintenanceCleaning the bobbin case ERemove the bobbin case Troubleshooting Lower Or breaksThread ten Fabric isStitches are SkippedThere is a high Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30 , 32 2000cover2-3.fm Page 2 Monday, October 4, 2004 402 PM

EX 660 specifications

The Brother EX 660 is a versatile and user-friendly embroidery machine that has garnered attention for its range of features tailored to both beginners and experienced crafters. This innovative machine combines advanced technology with user-centric design to deliver exceptional performance in embroidery tasks.

One of the standout features of the Brother EX 660 is its expansive embroidery area. With a generous embroidery field, users can create large and intricate designs without the need for constant repositioning of the fabric. This feature is particularly useful for quilting enthusiasts who want to incorporate detailed motifs into their projects.

Equipped with a variety of built-in designs and fonts, the Brother EX 660 empowers users to unleash their creativity. The machine houses hundreds of pre-installed embroidery designs, ranging from floral patterns to seasonal themes. Additionally, it offers a selection of fonts for monogramming, allowing users to personalize their creations effortlessly.

The Brother EX 660 also utilizes cutting-edge technology that simplifies the embroidery process. The machine features an easy-to-use LCD touchscreen display, which enables users to navigate through options and settings with ease. This user-friendly interface streamlines the process of selecting designs, adjusting settings, and monitoring progress.

Another significant characteristic of the Brother EX 660 is its compatibility with USB flash drives. This feature allows users to import custom designs from their computers or the internet, providing endless possibilities for creativity. Whether it's a unique personal design or a specific pattern found online, the machine can accommodate various file formats for added convenience.

In terms of ease of use, the Brother EX 660 boasts an automatic needle threader that saves time and minimizes frustration. This feature ensures a smooth and hassle-free start to any embroidery project. Additionally, the machine’s drop-in bobbin system is designed for quick and easy bobbin changes, enhancing overall efficiency.

The Brother EX 660 is also built with durability in mind. Its robust construction and high-quality materials ensure that the machine can withstand intensive use while delivering reliable performance. This makes it a great investment for anyone passionate about embroidery and sewing.

In conclusion, the Brother EX 660 emerges as an exemplary tool for embroidery enthusiasts. With its spacious embroidery area, extensive built-in designs, user-friendly technology, USB compatibility, and durable design, it stands out as a top choice. Whether you are a novice or an experienced embroiderer, this machine promises to enhance your crafting experience and inspire your creativity.