Kenmore Water System Step by Step Guides to Install, Bypass, Inlet Outlet Copper Tubes FIG, GO to

Page 12

SECTION3

STEP BY STEP GUIDES TO INSTALL

A. ASSEMBLE INLET-OUTLET ADAPTORS, OR PLASTIC BYPASS VALVE

 

S

[

Close

the

shut-off

valve

on

 

 

 

the

house

main

 

water

 

pipe,

C

 

near the water meter or pres-

 

sure tank, to turn off the wa-

 

ter.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[]Shut

 

 

off

the

gas

or

electric

 

 

 

supply

to

the

water heater.

 

 

[

Open

the

highest

 

and

lowest

 

 

 

water faucets in your house to

 

 

 

let water drain from the pipes.

 

N

 

Close

faucets after water has

 

 

drained.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[

If

not

already

done,

remove

i,JJ,aJ.J ,JJ,aJ.J

,JJ,a.

all

cardboard

or

plastic

pack-

i,a

,aJ.=J,J

,aJ.=.

i,J

J

,JJ,a.

ing

pieces

from

 

inside

the

 

 

 

 

 

 

 

 

 

i.t

 

.t,_,_.

softener.

Set

the

parts

bag

i,aJ

,aJ.=.

 

 

 

 

 

 

 

 

 

i.=.a._._,a i.=.a._._,a i.=.a._.

where

you can

easily

see it,

 

 

 

and get to parts as you need them.

;hutoff

Shutoff

--

Pressure

MeterPump

Electrical

GasPanel

Valv

[]INSTALL

SEARS

BYPASS

VALVE

AND

/ OR

THE INLET OUTLET COPPER TUBES (FIG.

4, 5

AND 6). All

needed

parts are

in the

parts

bag.

 

 

 

 

 

Note:

If you will not install the bypass valve because you will have a 3- valve bypass, skip step b, but do steps a and c.

O Visually check and remove any foreign materi- als from the valve inlet and outlet ports (FIG. 6). Carefully remove the two large plastic clips (you will use them). Check to be sure the turbine and

turbine support are firmly in place. (Fig. 6)

@BYPASS VALVE: If not already done, put a light coating of silicone grease on the o-ring seals and

slide onto the bypass valve. Push the bypass valve into the softener valve as far as it will go.

Snap the 2 large holding clips into place, from the top down as shown. (Fig. 7)

[] CAUTION...Be sure the clips snap firmly into place so the bypass valve will not pull out. (Fig. 7)

GO TO PAGE 3-4.

@INLET AND OUTLET COPPER TUBES: If not

already done, put a light coating of silicone grease on the o-ring seals and slide onto the cop- per tubes. Place the tubes into the valve inlet and outlet ports, or bypass valve ports, as far as they will go. Both tubes are the same and fit either

port. Tighten the installation nuts holding the copper tubes. (Fig. 7)

[] CAUTION...Be sure the clips snap firmly into place so the tubes will not pull out. (Fig. 7)

GO TO PAGE 3-3.

3 - 1 Deluxe Valve

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Deluxe valve Save this ManualOther About Your Water Ask At yourStore Or call Table Ofcontents 1BEFORE Installing Checks & Tests Safety GuidesBefore Installing Checks & Tests Unpacking the Water SoftenerCheck the softener for shipping damage. If you Parts DescriptionsWater System Tests Plan Your Installation Where to Install the Water SoftenerTer going through the softener must not be more than 120F TOOLS, Pipe and Fittings Other Materials NeededPipe and FII-rlNGS, Plan Drawing NPT X 3/4 Sweat Reducer Typical Threaded in and OUT Pipes to Softener Fittings Required not IdentifiedStep by Step Guides to Install Assemble INLET-OUTLET ADAPTORS, or Plastic Bypass ValveBypass Inlet Outlet Copper Tubes FIGInstalling Holding Clips Bypass Valve Turned Downward CopperInstall 3-VALVE Bypass Installing 3 Valve Bypass and PipesWhen looking at the front of the softener, the inlet When all pipe, fittings and valves make a goodLocate Water SOFTENER, and Connect Pipes Move the Softener Into PlaceMove Softener Into Place Typical Soldering ConnectionsConnect Valve and Salt Tank Drains Ffi Connect the Valve Drain HoseConnectsalt Tank Overflow TU Bing Pressure Test / Check for Leaks Previous caution notesHouse Main Water Shutoff Valves To Electrical Power Installgrounding Wire BetweenCold Water Pipe Grounding Water Meter Jumper Wire Grounding / ConnectGrounding / Connect to Electrical Power Transformer ConnectingRestart the Water Heater

Water System specifications

Kenmore Water System is a comprehensive water purification solution designed to enhance the quality of drinking water in residential settings. Known for its innovative approach, Kenmore has established itself as a trusted name in the industry, offering a range of products that cater to various consumer needs.

One of the standout features of the Kenmore Water System is its advanced filtration technology. The system typically incorporates a multi-stage filtration process that includes sediment filters, activated carbon filters, and advanced reverse osmosis. This multi-layer approach effectively removes contaminants such as chlorine, lead, bacteria, and other harmful substances, ensuring that the water is not only safe to drink but also tastes clean and fresh.

Another notable characteristic of the Kenmore Water System is its user-friendly design. Many products in the line are designed for easy installation and maintenance. With intuitive indicators for filter changes and straightforward setup procedures, users can enjoy the benefits of purified water without the hassle often associated with complex systems. The sleek designs of the water purifiers and softeners also make them an attractive addition to any kitchen or utility area.

In addition to traditional filtration methods, Kenmore has embraced innovative technologies, such as smart sensor technology. Some models feature Wi-Fi connectivity, allowing users to monitor their water quality and system performance remotely through dedicated apps. This technology not only enhances user convenience but also provides real-time insights into water consumption and filter status, promoting proactive maintenance.

Energy efficiency is another priority for Kenmore. Many systems are designed to reduce water waste and energy consumption, making them not only cost-effective in the long run but also environmentally friendly. This aligns with growing consumer awareness and preference for sustainable products.

Kenmore’s customer support is also commendable, with comprehensive warranties and readily available assistance to ensure that users can maximize their water system’s potential. From installation guidance to troubleshooting tips, the support provided reflects Kenmore’s commitment to customer satisfaction.

With a blend of advanced technology, user-friendly features, and effective performance, the Kenmore Water System stands out in the market, defining a new standard in residential water purification solutions.
Top Page Image Contents