Kenmore Water System Locate Water SOFTENER, and Connect Pipes, Move the Softener Into Place

Page 15

SECTION3

STEP BY STEP GUIDES TO INSTALL

C. LOCATE WATER SOFTENER, AND CONNECT PIPES

[]MOVE THE SOFTENER INTO PLACE

Move the softener into place, onto a level and

smooth surface. If needed, put a piece of 3/4"

plywood, at least 17" x 20", under the tank. Then

put spacers under the plywood to level the soft- ener. Do not put shims or spacers directly under

the tank, without the plywood. The weight of the softener, when full of salt and water, may cause the tank to puncture or break at the shim or spacer.

To move the softener, grip under the ridge on the salt tank sidewall and carefully rock back and forth, into position.

_J_ CONNECT THE SOFTENER (Refer to your

plan drawing on page 2-3, and to page 2-4 or

2-5. Read the IMPORTANT note on page 3-3. Then, measure, cut (thread if needed) and put all pipe and fittings together up to the main water

pipe, or to the bypass valve(s) you installed on page 3-3.

Notes:

MOVE SOFTENER INTO PLACE

shims

TYPICAL SOLDERING

CONNECTIONS

• Include adaptors, reducers, union fittings, etc., as needed.

Cut pipe lengths exact for correct aligning, and to

prevent stress on the softener valve.

Use pipe joint compound or Teflon tape on out- side pipe threads.

When all piping fits together...

...solder

all

sweat fittings.

...prime

and

cement

all CPVC joints.

...tighten

all

threaded

joints.

[] CAUTIONS:

Never solder fittings while connected to non-

metallic parts. Wait until soldered pipe has cooled

before connection (see fig. 11).

Be careful when putting pipe fittings together. Do not cross thread, and do not overtighten.

_W

ater Pipe

NOTE: To be certam heat wilt not travel down the pipe

and into the bypass valve (or instatlation adaptors),

wrap the bottom of the pipe and the bypass valve in a wet rag.

_1. Cut pipe to

f correct length,

Solder (WHEN

COOL, do Step

3),

I _'_3. CAREFULLY,

turn onto bypass valve and

tighten (use pipe

joint compound or Teflon tape).

3 - 4 Deluxe Valve

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

Image 15
Contents Save this Manual Deluxe valveOther About Your Water Ask At yourStore Or call Table Ofcontents Safety Guides 1BEFORE Installing Checks & TestsParts Descriptions Before Installing Checks & TestsUnpacking the Water Softener Check the softener for shipping damage. If youWater System Tests Plan Your Installation Where to Install the Water SoftenerTer going through the softener must not be more than 120F Other Materials Needed TOOLS, Pipe and FittingsPipe and FII-rlNGS, Plan Drawing NPT X 3/4 Sweat Reducer Fittings Required not Identified Typical Threaded in and OUT Pipes to SoftenerInlet Outlet Copper Tubes FIG Step by Step Guides to InstallAssemble INLET-OUTLET ADAPTORS, or Plastic Bypass Valve BypassCopper Installing Holding Clips Bypass Valve Turned DownwardWhen all pipe, fittings and valves make a good Install 3-VALVE BypassInstalling 3 Valve Bypass and Pipes When looking at the front of the softener, the inletTypical Soldering Connections Locate Water SOFTENER, and Connect PipesMove the Softener Into Place Move Softener Into PlaceFfi Connect the Valve Drain Hose Connect Valve and Salt Tank DrainsConnectsalt Tank Overflow TU Bing Pressure Test / Check for Leaks Previous caution notesHouse Main Water Shutoff Valves Grounding / Connect To Electrical PowerInstallgrounding Wire Between Cold Water Pipe Grounding Water Meter Jumper WireGrounding / Connect to Electrical Power Transformer ConnectingRestart the Water Heater

Water System specifications

Kenmore Water System is a comprehensive water purification solution designed to enhance the quality of drinking water in residential settings. Known for its innovative approach, Kenmore has established itself as a trusted name in the industry, offering a range of products that cater to various consumer needs.

One of the standout features of the Kenmore Water System is its advanced filtration technology. The system typically incorporates a multi-stage filtration process that includes sediment filters, activated carbon filters, and advanced reverse osmosis. This multi-layer approach effectively removes contaminants such as chlorine, lead, bacteria, and other harmful substances, ensuring that the water is not only safe to drink but also tastes clean and fresh.

Another notable characteristic of the Kenmore Water System is its user-friendly design. Many products in the line are designed for easy installation and maintenance. With intuitive indicators for filter changes and straightforward setup procedures, users can enjoy the benefits of purified water without the hassle often associated with complex systems. The sleek designs of the water purifiers and softeners also make them an attractive addition to any kitchen or utility area.

In addition to traditional filtration methods, Kenmore has embraced innovative technologies, such as smart sensor technology. Some models feature Wi-Fi connectivity, allowing users to monitor their water quality and system performance remotely through dedicated apps. This technology not only enhances user convenience but also provides real-time insights into water consumption and filter status, promoting proactive maintenance.

Energy efficiency is another priority for Kenmore. Many systems are designed to reduce water waste and energy consumption, making them not only cost-effective in the long run but also environmentally friendly. This aligns with growing consumer awareness and preference for sustainable products.

Kenmore’s customer support is also commendable, with comprehensive warranties and readily available assistance to ensure that users can maximize their water system’s potential. From installation guidance to troubleshooting tips, the support provided reflects Kenmore’s commitment to customer satisfaction.

With a blend of advanced technology, user-friendly features, and effective performance, the Kenmore Water System stands out in the market, defining a new standard in residential water purification solutions.