Kenmore 625.38426 owner manual Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve

Page 11

ASSEMBLE INLET OUTLET ADAPTORS, OR SINGLE BYPASS VALVE

Complete the following steps to assemble the adaptors or bypass valve.

1.Close the shutoff valve on the house main water pipe, near the water meter or pressure tank, to turn off the water. See Fig. 7.

2.Shut off the gas or electric supply to the water heater. See Fig. 7.

3.Open the highest and lowest water faucets in your

house. This will let water drain from the pipes. Close faucets after water has drained.

4.Remove the main cover. See Fig. 8. Pull outward on two (2) tabs to release.

The salt hole cover remains attached to the main cover

when removed. Set both covers aside so they will not get scratched or broken.

INSTALL SEARS BYPASS VALVE AND / OR THE INLET OUTLET THREADED ADAPTORS

NOTE: If you will not install the bypass valve because you will have a three (3) valve bypass, skip steps 6 & 7, but do steps 5 and 8.

5.Visually check and remove any foreign materials from the valve inlet and outlet ports. See Fig. 9. Carefully remove the two large plastic clips (you will use them). Check to be sure the turbine and turbine support are firmly in place. See Fig. 10.

BYPASS VALVE:

6.Put a light coating of silicone grease on the o-ring seals and slide onto the bypass valve.

7.Push the bypass valve into the softener valve as far as it will go. Snap the two large holding clips into place, from the top down as shown. See Fig. 11.

CAUTION: Be sure the clips snap firmly into place so the bypass valve will not pull out. See Fig. 11.

INLET AND OUTLET THREADED ADAPTORS:

8.Put a light coating of silicone grease on the o-ring seals and slide into the threaded adaptors. Push the adaptors into the valve inlet and outlet ports, or bypass valve ports, as far as they will go. Both adaptors are the same and fit either port. Snap the two large holding clips into place, as shown. See Fig. 11.

CAUTION: Be sure the clips snap firmly into place so the tubes will not pull out. See Fig. 11.

Shutoff

Shutoff

.

Pressure

Valve

Valve

d/

Tank

Pump

Electrical

Panel

FIG. 7

Salt Hole Cover

FIG. 8

INSTALLING BYPASS VALVE, AND/OR

INLET AND OUTLET THREADED ADAPTORS

Valve Outlet

Included with

Softener

Valve Inlet_

_.

Included with

 

 

 

 

Softener

 

 

FIG. 9

Questions? Call The Kenmore Water Line 1-800-426-9345

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents NSF/ANSI Save this ManualTEN Year Limited Warranty Against Leaks Warranty on Water SoftenerONE Year Limited Warranty on Water Softener Three Year Limited Warranty on Electronic PartsQuestions? Questions? Call The Kenmore Water Line Inspect Shipment Parts Descriptions Small PartsPipe Proper Order to Install Water Treating EquipmentPlan Your Installation Tools NeededWhere to Install the Water Softener Typical InstallationDraw Your Pipes Fittings Suggested Slab Foundation InstallationOUT Adding a pressure reducing valve may reduce the flow Before Installing Checks & TestsInlet and Outlet Threaded Adaptors Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveBypass Valve Bypass Valve Turned Downward Installing Holding ClipsValve Bypass Connect the Softener Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseLeak Test House Main Water Shutoff ValvesSingle Bypass Cold Water Pipe Grounding Water Meter Jumper WireConnecting Transformer Electrical Power Outlet for Your SoftenerRestart the Water Heater Install CoversProgram the Timer Hardness Number SET Present Time of DAYSET Water Hardness Number Recharge Time SET Regeneration TimeSanitize Your Water Softener AS Follows Sanitize the Water SoftenerRemoving Additives Adding Salt to the Storage TankWater Softening Salt with Iron Unit plugged Into a continuously live outlet? Check List of STEP-BY-STEP Guides to InstallMenu Selections SettingsRecharge NOW Recharge TonightOptions Play Units Service Mode Kenmores Ultra Cleansing Feature Regeneration Soft Water Service and RegenerationService Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseElectronics Soft Water Service and Regeneration Automatic BypassWater Flow Through Softener Fast Rinse Salt Bridge Salt BridgeIron from Resin BED Keeping the Water Softener Clean Nozzle & VenturiFreezing Drain ALL Water from SoftenerCorrection ProblemcauseChecklist to Help YOU Save Money Bypass Valves Timer Code H46Pressure Drop PSI vs. Flow Rate GPM Eration Check Wiring SchematicFaceplate Always Make These Initial Checks FirstCode Most Likely Possible ProblemProcedure for Removing Error Code From Faceplate Manual Initiated Electronics DiagnosticsTimer PWA Replacement MAX. Backwash Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN Brine RinseServicing the Valve DisassemblyAssembly To Relieve PressureFill Cycle Valve Service CycleService Cycle Water Flow Through the SoftenerFast Rinse Cycle Valve Backwash CycleFast Rinse Cycle Backwash CycleQuestions? Call The Kenmore Water Line Ing Decal Water Softener Complete KeyNoInlet Outlet Grounding Clamps Part Number Part Description Brine Valve Assembly\1110 o Key Part No. Number Part Description Your Home

625.38426 specifications

The Kenmore 625.38426 is a mechanical marvel in the world of household appliances, specifically designed for those who value efficiency, convenience, and performance in their laundry tasks. As a top-load washing machine, this model is perfect for families or individuals looking for a reliable and effective solution for their washing needs.

One of the most notable features of the Kenmore 625.38426 is its impressive capacity. With a large drum that can handle up to 3.8 cubic feet of laundry, this machine can accommodate a significant amount of clothing in a single load, saving precious time and energy. This is especially beneficial for larger households or anyone with a heavy laundry routine.

The washing machine is equipped with a variety of wash cycles tailored to meet various fabric care requirements. Users can choose from multiple settings, including delicate, normal, heavy-duty, and quick wash cycles. This versatility ensures that delicate garments are treated with extra care while tough stains on durable fabrics can be effectively tackled.

In addition to its array of cycles, the Kenmore 625.38426 boasts innovative technologies that enhance its functionality. The machine features a dual-action agitator that effectively moves clothes throughout the wash cycle, ensuring thorough cleaning without causing damage to the fabrics. This means users can confidently clean a wide range of clothing items, from casual wear to more sensitive materials.

Energy efficiency is another critical aspect of the Kenmore 625.38426. This model utilizes advanced technology to minimize water and electricity consumption while delivering optimal cleaning performance. This is not only beneficial for the environment, but it also translates into cost savings on utility bills over time.

The control panel of the Kenmore 625.38426 is user-friendly, featuring clearly labeled options and easy-to-understand settings. This intuitive design allows users to quickly select their desired wash cycle without any confusion.

Durability and longevity are also hallmarks of this washing machine. Constructed with high-quality materials, the Kenmore 625.38426 is designed to withstand regular use while maintaining its performance over the years.

In summary, the Kenmore 625.38426 emerges as a powerful and efficient washing machine that combines capacity, versatility, and energy efficiency. With its user-friendly features and robust construction, it stands out as a top choice for those looking to invest in a reliable laundry appliance that meets modern household demands.
Top Page Image Contents