Kenmore 625.38888 owner manual Keeping the Water Softener Clean, Cleaning Nozzle & Venturi

Page 17

[i!i !! :; _ !! :; _ !! :; :i SECTION 3

CARE OF YOUR WATER SOFTENER

B. KEEPING THE WATER SOFTENER CLEAN

NOZZLE & VENTURI

A clean nozzle and venturi (FIG. 11) is a must for the softener to work right. This small unit moves brine from the salt storage tank to the resin tank duringre-

generation. If it becomes plugged with sand, silt, dirt, etc., the softener will not work and you will get hard water.

To get to the nozzle and venturi, remove the softener top cover. Be sure the softener is in service cycle (no

water pressure at nozzle and venturi), then turn off

the cap from the nozzle and venturi housing. Do not lose the large o-ring seal. Lift out the screen support

and screen, then the nozzle and venturi. Wash and

rinse the parts in warm water until clean. If needed, use a small brush to remove iron or dirt. Also check

and clean the gasket, flow plugs and screens.

Cleaning Nozzle & Venturi

Cap _

O-ring Seal --.__.___

Screen Support _._._..

Screen

*Flow Plug

Nozzle&_itkUell

_

_

Screen

tered directly over the smell holes in the nozzle & venturi

housing.

*Flow Plug

(HVDC)

Nozzle & Venturi

Carefully replace all parts in the correct order. Lu- bricate the o-ring seal with silicone grease or Vase-

line and place in position. Install and tighten the

cap, by hand only. Do not overtighten, which may break the cap or housing.

IRON FROM RESIN BED

Your water softener takes hardness minerals (cal-

cium and magnesium) out of the water. Also, it can

control some "clear water" iron. See maximum al-

lowed in the specifications on page 4-1. With clear water iron, water from a faucet is clear when first

put into a glass. After 15 to 30 minutes, the waterbe- gins to cloud or turn rust colored. A water softener WILL NOT remove any iron which makes the water cloudy or rusty as it comes from the faucet (called red water iron). To take red water iron out of watei,

or over the maximum of clear water iron, an iron ill-

Housing

*Install with numbered side up, concave

side down. Be sure the largest flow plug is located in the nozzle & venturi housing.

ter or other equipment is needed. Your local Sears store has trained people to help you with iron water problems.

If your water supply has clear water iron, even

though less than the maximum allowed, regular resin bed cleaning is needed. Your local Sears store has resin bed cleaner, Item No. 42-34426 for this. Clean the bed at least every 6 months. If iron shows

up in the soft water before 6 months, clean more

often. Printed instructions are on the resin bed cleaner bottle.

3-2

Problems, Questions? Call 1- 800- 426- 9345 Kenmore Water Line

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Save this Manual Owners ManualFull Three Year Electronics Warranty Full ONE Year Warranty on Water SoftenerFull TEN Year Warranty Against Leaks Sears Residential Water SoftenerWater Softener Start UP Care of Your Water SoftenerWater Softener Start UP Safety GuidesManual unless otherwise noted Check List of STEP-BY-STEP Guides to InstallTo are Unless OtherwiseSET Language Program the TimerSET Present Time of DAY DownSET Water Hardness Number If YOU Need Help Programming the TIMER, Call Toll FreeSelect Hardness NumberStorage tank Sanitize the Water SoftenerWater Softening Salt with Iron Remov Adding Salt to the Storage TankFaceplate Leci Faceplate Timer FeaturesChange Mode PPMLect Water Flow Through Kenmores Ultra Cleansing FeatureService Water Flow Through Softener in Backwash RegenerationWater Flow Through Softener in Fill Automatic Bypass Water Flow Through Softener in Fast RinseElectronics Salt Bridge Salt Adding to the Storage TANK, Salt BridgeSalt Bridge Iron from Resin BED Keeping the Water Softener CleanCleaning Nozzle & Venturi From Freezing Protect the Water SoftenerProgram Checklist ... to Help YOU Save MoneyBypass Valves Dimensions / SpecificationsSingle Bypass Valve BypassPressure Drop PSI vs. Flow Rate GPM Vance Regeneration Check TroubleshootingMake These Initial Checks First Most Likely CodePossible Defect Less LikelyHF45 shows Brining Cycle Flow Rates Gallons PER MINBackwash Brine RinseDisassembly Rotary Valve ServiceAssembly Lieve PressureFill Cycle Water Flow Through the Softener Valve Service CycleSection Backwash Cycle Fast Rinse Cycle Water Flow Through the Softener ValveRepair Parts for Water Softener KEY Part Water Softener CompleteNO. Number DescriptionInlet Outlet Grounding Clamps Repair Parts for Water Softener Repair Parts for Water Softener Valveassembly Bypass Installation Valve Valve AssemblyModel Part DescriptionWater Softeners

625.3888, 625.38888 specifications

The Kenmore 625.38888 and 625.3888 are high-efficiency water softeners that cater to households with diverse water quality needs. Known for their advanced technology and reliable performance, these models are designed to tackle hard water issues while enhancing water quality and extending the lifespan of plumbing appliances.

One of the main features of the Kenmore 625.38888 and 625.3888 is their highly efficient ion-exchange process. This process effectively removes hard minerals such as calcium and magnesium from the water, which helps to prevent scale buildup in pipes, appliances, and fixtures. By softening the water, these models improve the effectiveness of soaps and detergents, leading to cleaner dishes, brighter laundry, and reduced soap scum.

Both models boast a user-friendly digital control panel, which allows homeowners to easily monitor and adjust settings. This digital interface includes features such as a programmable regeneration cycle, which can be set based on water usage patterns. This ensures that the softener operates efficiently and only regenerates as needed, saving salt and water in the process.

Another characteristic worth mentioning is the high-capacity resin tank used in these models. With a robust design, the resin tank can handle larger volumes of water, making it ideal for families or homes with significant water demands. Additionally, the Kenmore 625.38888 and 625.3888 are equipped with a corrosion-proof brine tank, which enhances durability and reduces the risk of leaks or damage over time.

The installation of these water softeners is straightforward, allowing users to have them up and running with minimal hassle. Along with a comprehensive installation guide, these models typically come with essential components needed for hook-up. The compact design ensures that they can fit in smaller spaces without overwhelming the area.

In terms of maintenance, the Kenmore 625.38888 and 625.3888 require minimal upkeep. Regularly checking and refilling the salt in the brine tank ensures optimal functioning, while periodic cleaning of the resin tank maintains efficiency.

In summary, the Kenmore 625.38888 and 625.3888 water softeners provide a reliable solution for hard water challenges. With their efficient ion-exchange technology, user-friendly controls, high-capacity design, and easy installation and maintenance, these models are well-suited for various households looking to enhance their water quality.
Top Page Image Contents