Harman-Kardon AVR 254 owner manual Number of Speakers, Adjust Crossover Frequencies Menu, Sub Mode

Page 46

ADVANCED FUNCTIONS

NOTE: All of the speaker setup submenus include the Exit and Back options as shown at the bottom of Figure 58. To return to a previous menu without making any changes, select Exit. To save the current settings, select the Back option.

If you previously saved EzSet/EQ results in this setup position and you wish to reconfigure the speakers from scratch, select the Reset option.

For best results, we recommend configuring the speakers in this order, although it may differ from the order in which the submenus appear in the Manual Speaker Setup menu: Number of Speakers, Crossover (Size), Sub Mode, Distance and Level Adjust.

Number of Speakers

Move the cursor to the Number of Speakers line and press the Set Button. See Figure 61.

Figure 61 – Number of Speakers Menu

The Number of Speakers menu lists each of the speaker groups. Program the correct setting for each group: ON when the speakers are present in the system, and OFF for positions where no speakers have been installed. The Front Left & Right speakers are always ON and may not be disabled. Any changes made to the system configuration will be reflected in the total number of speakers displayed at the top of the screen.

The setting for the surround back speakers includes a third option: Zone 2. The AVR 254 is capable of multizone operation, allowing place- ment of a pair of speakers in another room. Listeners in the remote room may enjoy either the same program as in the main room or a different source. The AVR 254’s assignable surround back amplifier channels make multizone operation easier than ever, since an external power amplifier is not required. Simply select the Zone 2 option at this line, and connect the Surround Back Speaker Outputs to loudspeakers located in the remote room. The main room will be configured automatically for up to 5.1 channels. See the Multizone Operation section for more information.

The settings in this menu affect a number of aspects of the AVR’s operation, including the remainder of the speaker setup process and the availability of various surround modes at any time.

When you have finished programming the number of speakers in the system, select the Back option to insure the settings are saved correctly. You may use the Back/Exit Button, and the settings will be saved.

Adjust Crossover Frequencies Menu

After you have programmed the number of speakers in the system, the AVR will return to the Manual Speaker Setup menu, similar to the one shown in Figure 46. Navigate to the Crossover (Size) line and press the OK Button to display the Adjust Crossover Frequencies menu (see Figure 62).

Figure 62 – Adjust Crossover Frequencies Menu

The AVR will only display those speaker groups which you programmed in the Number of Speakers menu.

Refer back to Step One, where you determined each speaker’s crossover. For the main speakers, this is the lowest frequency the speaker reproduces well; and for the subwoofer, it’s the highest.

For each main speaker, select one of the seven crossover frequencies: 40Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz or 200Hz. If the crossover frequency you determined in Step One is below 40Hz, select the first option, “Large”. This setting doesn’t refer to the speaker’s physical size, but to its frequency response, which is also called “full range”. This means the speaker is capable of playing sounds throughout the frequency spectrum, from the high pitches to the bass.

Specify the size of the subwoofer’s transducer as 8, 10, 12 or 15 inches.

Make a note of each speaker group’s crossover setting in Table A3 in the appendix.

When you have finished entering the settings, remember to select Back, not Exit.

Sub Mode

Move the cursor to the Sub Mode line to program bass management for the subwoofer. The subwoofer’s setting depends upon how you programmed the front left and right speakers.

•If you set the front speakers to a numeric crossover frequency, the subwoofer setting will be LFE, and you won’t be able to change it. All low-frequency information will always be sent to the subwoofer. If you don’t have a subwoofer, we recommend that you either upgrade to full-range speakers or add a subwoofer to your system at the earliest opportunity.

•If you set the front speakers to LARGE, you may select between two possible settings for the subwoofer.

L/R+LFE: This setting sends all low-frequency information to the subwoofer, including both information that would normally be

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents AVR Safety Information Important Safety InstructionsImportant Safety Information Staple Invoice Here Table of Contents Harman Kardon AVR 254 7.1-Channel Audio/Video Receiver IntroductionThank you for choosing a Harman Kardon product Audio SectionAudio/Video Inputs Supplied AccessoriesAudio Inputs Digital Audio InputsVolume Knob Turn this knob to raise or lower the volume FRONT-PANEL ControlsAVR Info Message Display Speaker/Channel Remote FRONT-PANEL Connections REAR-PANEL Connections Is not available in Alaska and HawaiiTo that source Hdmi Remote Control Functions Page Alphanumeric Keys Use these buttons to enter numbers for Typical Home Theater System Introduction to Home TheaterSurround Modes Multichannel AudioTypes of Connections Connecting Source Devices to the AVRConnections Speaker ConnectionsAudio Connections Digital AudioVideo Connections FM antenna uses a 75-ohm F-connector. See FigureAntennas Digital VideoRS-232 Serial Port Front Speaker Placement Speaker PlacementPlacement of Surround Speakers in a 5.1-Channel System Placement of Surround Speakers in a 7.1-Channel SystemSubwoofer Placement Step Two Connect the Subwoofer InstallationStep One Connect the Speakers Step Three Connect the AntennasAudio Connections for non-HDMI sources Hdmi ConnectionsVideo Connections for non-HDMI sources Connect an Audio/Video Recorder PVD, DVR or TiVo Connect a CD Player or Any Audio-Only Device Connect a Tape Deck or Any Audio-Only RecorderStep Five Connect the Video Display Connect a Portable Audio PlayerStep Seven Insert Batteries in Remote Step Six Plug in AC PowerStep Eight Program Sources Into the Remote Turn on your source device Enter a code from , aboveSelect one or both Step Eleven Turn On the AVRTwo steps are required the first time you turn on the AVR AVR Power On and Source Selectors Using the On-Screen Menu System Initial SetupConfigure the AVR 254 Using EzSet/EQ Technology Selecting Cancel returns to the Speaker Setup menu Speaker Setup Menu ScreenSet Up Sources Audio and Video Input SelectionChannel Direct Inputs HDMI-equipped multichannel disc playerAdjust Lip Sync You are now ready to begin enjoying your new receiverOperation Source Selection Using the TunerAVR defaults to automatic tuning, meaning each press If a video source is playing and there is no picturePress the OK Button to store the new preset On screen when a video display is in useTo store a channel in one of the 40 preset locations RecordingSelecting a Surround Mode Stereo Jack InputAdvanced Functions Analog Audio SignalsDigital Audio Signals Audio Processing and Surround SoundIndicates that no surround information is present Virtual Surround Dolby Virtual Speaker Reference or WideDolby Surround Settings Night ModeStep Three Manual Setup Menu Manual SetupStep Two Measure Speaker Distances Sub Mode Adjust Crossover Frequencies MenuNumber of Speakers Adjust Speaker Distance Menu Step Four Setting Channel Output Levels ManuallyMake sure all speakers have been connected correctly Off For normal listening Audio Effects MenuSports For sporting events Video AdjustmentsNature For programs shot outdoors, in a natural setting Movie For movies and many television broadcastsContrast Adjustment How to Adjust the Custom Picture SettingsBrightness Adjustment Color AdjustmentOperating the Multizone System Installing a Multizone SystemMultizone Operation OK Button to display the Zone Control menu. See FigureMenu Appearance System SettingsGeneral AVR Settings Menus and displays English, French, Spanish or GermanProcessor Reset Advanced Remote Control FunctionsResetting the Remote Punch-Through ProgrammingMemory Troubleshooting Guide Appendix Appendix Default settings, worksheets, remote product codesTable A2 Source Setting Defaults Table A1 Recommended Source Component ConnectionsTable A3 Speaker/Channel Setting Defaults Table A4 Delay Setting DefaultsTable A6 Audio Effects Settings Table A5 Source SettingsTable A7 Video Modes Settings Table A10 System Settings Table A9 Remote Control CodesTable A8 Surround Modes Table A11 Zone 2 Settings Table A12 Surround ModesMovie Back channel 0 or .1, EX Analog 2-channel Tuner Mode Group Enveloping sound field is desiredExperience Tuner Music adds a surround back channel Analog 2-channel TunerPerformance Surround Mode Description Incoming Bitstream or SignalRate used on DVD-Video discs DTS-ES MatrixChannels Tuner PCM 32kHz, 44.1kHz or 48kHz Channel Stereo Appropriate when a subwoofer is usedChannel Stereo Analog Bypass39 40 Table A13 Remote Control Function List AVR DVDTable A13 VCRAiwa Table A15 Remote Control Product Codes AUX-HDTV Table A14Table A16 Remote Control Product Codes AUX-VCR Table A17 Remote Control Product Codes AUX-CD Table A18 Remote Control Product Codes DVD Table A19 Remote Control Product Codes SATTable A23 Remote Control Product Codes Table A21 Remote Control Product Codes CBLTable A22 Remote Control Product Codes Table A24 Remote Control Product Codes AUX- TiVOPage Page AVR 254 Technical Specifications DTS
Top Page Image Contents