Electronic Faucet, Operations, DRY Test

Distance SW6

OPERATIONS

Electronic Faucet

Operation and Installation

Instructions for Electronic

Faucets-Battery-Powered

The battery-powered faucet is designed for ease of installation and provides a reliable, convenient, economical and sanitary system for high-volume users, such as hospitals, transportation terminals, restaurants, schools, sports arenas, office buildings and municipalities. It can be installed by one tradesman without electrical hook-up.

Operation:

1.The faucet operates by emitting a continuous infared beam from the sensor.

2.As the user enters the beam’s effective range, a red light flashes one time to alert the user that the faucet will operate. As long as the user is in the beam’s range, the beam is reflected into the receiver circuitry and the system will operate.

3.When the user exits out of range, the sensor sends a signal to the solenoid for closure. The sensor then automatically resets and is ready for the next user.

4.Low battery indicator light comes on when battery is low.

Caution: Avoid installing the faucet where sensor faces a stainless steel wall or other reflective surface within the active range of sensors. Avoid facing another infrared sensor. It may cause faucet to activate unnecessarily.

NOTE: The reset button must be pressed after changing the battery in order to ensure the faucet functions properly.

INSTALLATION INSTRUCTIONS

DRY TEST

ATTENTION: To insure proper operation, before installing the faucet, a “DRY TEST” is recommended.

1.Take off the control box lid (13) by removing screws (12) with hex wrench.

2.Connect the sensor eye connector (20) at the end of the sensor eye cable (18) onto the circuit board (24) inside the control box (10) Refer to illustration “A”.

3.Slide battery housing out of control box (10) and install batteries (included) and slide battery housing back into control box (10). Insert the battery housing connector onto the circuit board. The lights on the circuit board should blink red/green/red.

4.Place your hand in front of the sensor (23) to operate the faucet and listen for a “clicking” sound.

5.Remove your hand and listen for a softer “clicking” sound. The “clicking” sounds

Circuit board	Circuit board		AC/DC switch
A side view	front view		AC/DC switch
A side view	front view
		DIP	DC receptor
	AC	switches
	AC
	receptor
	Sensor
	eye
	cable pin
	receptor
Solenoid				Reset
Solenoid				button
pin		Sensor		button
pin
receptor
receptor		distance
		distance	Green	Red
			Green	Red

indicate that the faucet is working properly. If there is no light or sound, please contact Moen at 1-800-289-6636.

6.The sensors are equipped with angular adjustments. The factory setting is in the center or straight position from the faucet. Adjustment is most easily performed before the faucet is installed. The adjustment is located inside the faucet body (1) behind the LED indicator light (25) Refer to illustration “B”.

7.If you are ready to install the faucet, disconnect the sensor eye connector (20) at the end of the sensor eye cable (18) from the circuit board (24).

8.Attach supply rod (6) into threads located at the bottom of the faucet body (1). If needed, snug the supply rod (6) with a “8 mm” hex wrench. Attach compression reducer (28) to the supply rod (6). Also attach compression adapter (7) to the solenoid valve outlet.

9.Attach the mounting bolts (2) to the faucet body. If needed, snug mounting bolts (2) with Phillips screwdriver.

10.Slide gasket (3) over sensor eye cable and onto faucet.

11.Set faucet on sink and install slotted washers

(4) and mounting nuts (5). Tighten mounting nuts (5) to secure the faucet to the sink.

12.Connect the sensor eye connector (20) at the end of the sensor eye cable (18) onto the circuit board (24). Properly seat both the sensor eye cable seal and cable into the control box slot on the left. Reinstall control box lid (13) and tighten screws (12) to insure the control box is water-resistant. NOTE: make sure that the rubber seal plug is in installed in the AC adapter control box slot

(on the right).

13.Connect 3/8” copper tube (supplied) between the supply rod (6) and the solenoid valve (17). Tighten compression fittings.

14.Insert white nylon washer (9) into swivel nut on filter body inlet.

15.A) For standard (pre-tempered or cold water) installation, attach water supply to inlet of in-line filter/check valve body.

B)If a tempered water installation is needed, attach mixing/check valve (optional) to the inlet of in-line filter/check valve body. Connect water supply lines to mixing/check valve. Refer to illustration

“C”. NOTE: USE THREAD SEAL TAPE FOR ALL THREADED CONNECTIONS.

C)Refer to Illustration D for the optional mixing tee installation.

16.Turn on water and check for leaks. Place hand in front of sensor to activate water. Remove hands and the water should stop. If not, refer to troubleshooting guide.

17.For timing adjustments, refer to instructions on the inside of the control box lid. Refer to Illustration E.

A)Note: Be sure to depress the re-set button, located on the circuit board, after each adjustment.

B)The factory settings are: Sensor Distance Adjustment = approximately 3.5 inches from the lens Time Delay to shut-off after hands are removed = 1 sec seconds

Auto – shutoff = 30 seconds

ECONTROL BOX INSTRUCTIONS

	adjustor	LED
	LED	LED
Sensor		B
Lens	23 Sensors

18 Sensor

Eye Cable

Compression adapter

Optional Supply Tube provided by installer

Compression adapter

Optional

Supply

Tube

provided

by installer

ADJUSTMENTS: (DIP Switches):

1. Shut-off time delay3. Sensor Distance: after hands are removed:

Time Delay	SW1	SW2	SW3	3.5 – 12"	on
1 Sec	on	on	on	10 – 24"	off
2 Sec	on	on	off	4. Faucet Setting:
3 Sec	on	off	on	4. Faucet Setting:
4 Sec	on	off	off	Setting	SW7	SW8
5 Sec	off	on	on	Faucet	on	off
6 Sec	off	on	off	SENSOR DISTANCE ADJUSTMENT
7 Sec	off	off	on	SENSOR DISTANCE ADJUSTMENT
8 Sec	off	off	off	(SDA): Preset at factory. If
2. Auto Time-Out Feature:				adjustment is needed; Locate
2. Auto Time-Out Feature:				potentiometer with Phillips Head
Time-Out	SW4	SW5		adjuster screw. Turn adjuster screw
0 Sec	on	on		clockwise to increase SDA, counter
15 Sec	on	off		clockwise to decrease SDA.
30 Sec	off	on
60 Sec	off	off

8301 specifications

The Moen 8301 is a versatile and innovative pull-down kitchen faucet designed to enhance both the aesthetic and functional dynamics of a modern kitchen. Renowned for its blend of style and practicality, the Moen 8301 showcases several features and technologies that cater to the needs of everyday users.

One of the standout features of this faucet is its sleek design, which complements a wide range of kitchen styles. The Moen 8301 is available in various finishes, including chrome and spot-resistant stainless steel, ensuring that homeowners can find the perfect match for their decor. Its high-arc spout not only adds to the visual appeal but also provides ample space for filling large pots and cleaning tall items.

Equipped with Moen's exclusive Power Boost technology, the 8301 delivers a powerful boost of water flow at the push of a button. This feature is particularly helpful for tasks that require extra water flow, such as rinsing or filling pots quickly. The spray head also includes a toggle button that allows users to switch between a steady stream and a powerful spray, offering versatility for different kitchen tasks.

Another significant characteristic of the Moen 8301 is its ease of installation and use. The faucet comes with a standard single-hole mount, making it suitable for quick DIY installation. The pull-down spray head is ergonomically designed for ease of use, allowing users to maneuver and direct water wherever needed without hassle.

The Moen 8301 also incorporates advanced technologies aimed at reducing maintenance and ensuring long-lasting performance. The faucet features a durable ceramic disc cartridge, which offers reliable operation and prevents leaks. Moreover, its Duralock quick connect system simplifies the installation process, allowing users to effortlessly connect the water supply lines.

Additionally, the Moen 8301 is designed with sustainability in mind. It meets the EPA WaterSense criteria, which means it is engineered to conserve water without sacrificing performance. This is particularly beneficial for environmentally conscious homeowners looking to reduce their water consumption.

In conclusion, the Moen 8301 pull-down kitchen faucet is a remarkable blend of functionality, aesthetics, and technology. With features like Power Boost technology, a high-arc design, and easy-to-use functionalities, it stands out as a reliable choice for any contemporary kitchen. Its durable construction and emphasis on water conservation make it an investment that combines both style and sustainability.