American Standard 3355 installation instructions 7301116-100 Rev. B

INSTALLATION INSTRUCTIONS

AFWALL ADA RETROFIT FLUSH VALVE

WALL-MOUNTED TOILETS

Model 3355, 3356, 3357, 3358

Meets the American Disabilities Act Guidelines and ANSI A117.1

Requirements for the Physically Challenged

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure thisproduct is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

!CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR

HANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY!

NOTE: For proper operation product requires a minimum of 30 psi working line pressure

RECOMMENDED TOOLS AND MATERIALS

Closet Carrier Support	Regular Screwdriver	Sealant	Carpenters Level
Putty Knife	Adjustable Wrench	Tape Measure	Flush Valve

U S E

1Pictures may not exactly define contour of china

	FINISHED WALL	1" N.P.T. OR C.W.T. SUPPLY			When installed,
	AS REQUIRED TO FLUSH VALVE
	660mm				top of seat shall be
			C/L		between 17" and 19"
	(26)
		121mm			(432mm and 483mm)
	73mm	(4-3/4)
					from the finished
	(2-7/8)
			356mm		floor.
	470mm
			(14)
	(18-1/2)			292mm
			(4) 22mm
	1-1/2 SPUD			(11-1/2)
19mm	C/L OF SEAT POST		(7/8)
	HOLES 140 mm
			HOLES
(3/4)	(5-1/2) CENTER
83mm	368mm		229mm
(3-1/4)	(14-1/2)			191mm
			(9)
	419mm			(7-1/2)
	(16-1/2)
62mm	FINISHED	C/L OF		133mm
	FLOOR			(5-1/4)
(2-3/8)		OUTLET
133mm
(5-1/4)	32mm
	(1-1/4)
	FOR WALLS UP TO 1" IN THICKNESS FOR EACH INCH
	ADDITIONAL THICKNESS OF WALL ADD 25mm (1) TO
	MEASUREMENT SHOWN
	FINISHED WALL	1" C.W.T. OR N.P.T. SUPPLY
		AS REQ'D NOT FURNISHED
	95mm		121mm
	(3-3/4)		(4-3/4)
	660mm		254mm
	(26)		(10)
	38mm (1-1/2) DIA. HOLE IN WALL		38mm	C/L
	76mm(3) DIA. HOLE IN WALL		(1-1/2)
	FOR 1-1/2 SPUD
	470mm	41mm	VACUUM BREAKER		298mm
	(18-1/2)				(11-3/4)
			356mm
		(1-5/8)
				(14)
	C/L OF SEAT POST HOLES
	140mm(5-1/2) CENTERS	89mm
(3/4)		(4)
	368mm
19mm		(4) 22mm (7/8)		229mm
	(14-1/2)
83mm					191mm
		DIA. HOLES		(9)
(3-1/4)	419mm				(7-1/2)
	(16-1/2)
	FINISHED		C/L OF		133mm
62mm 3/8)-(2 133mm	FLOOR				(5-1/4)
			OUTLET
	1/4)-(5
	32mm
	(1-1/4)

Refer to instructions supplied with wall carrier for proper installation of 4-bolt support system wall cavity requirements and rough-in information for waste outlet piping.

2FIXTURE MOUNTING

Fixture studs should project 1-7/8" (48mm) from face of finished wall.

FINISHED

WALL

1-7/8" (48mm)

(4) STUDS

Side View

Front View

S A V E F O R F U T U R E

Saniwares

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © A m e r i c a n S t a n d a r d I n c . 2 0 0 7

7301116-100 Rev. B