Craftsman 139.53699SR, 139.53315SR, 139.53625SR specifications Serat,on of Your Opener, Care

Page 3

O Serat,on of Your Opener

BEFORE YOU PROCEED, PLEASE READ THE

SAFETY RULES ON PAGE 2 AND OPERATING INSTRUCTIONS ON THIS PAGE CAREFULLY.

TO AVOID DIFFICU/L,TY DURING INSTALLATION, DO NOT RUN OPENER UNTIL INSTRUCTED TO DO SOs

USING THE OPENER

Your opener can be activated by any of the following devices:

1_The 3-Function Transmitter. Hold the LARGE push but- ton down until the door starts to move..

2_ The Well Push Button° Hold push button down until the door starts to move.

3.The Key Switch or Touch Code Transmitter accessories° Described on page 4

OPENING THE DOOR MANUALLY

THE DOOR SHOULD BE FULLYCLOSEDIF POSSIBLF.LWEAK OR BROKEN SPRINGS COULD ALLOW AN OPEN DOOR TO FALL RAPIDLY_PROPERTYDAMAGEOR SERIOUSPERSONAL INJURY COULD RESULT. DO NOT USE EMERGENCYHANDLE TO PULL

DOOR OPEN OR CLOSED.

The door can be operated manually by disconnecting it from the opener. Pull down sharply on the red emergency release handle and lift the door manualty.. To automatically reconnect the door to the opener, press the Wall Push Button.

LOCKOUT FEATURE: prevents trolley from reconnecting automatically, If you need to use this feature, pull emergency handle down and back (toward the opener)_Trolleywill remain "Lock, d-Out" and door can be raised and lowered manually. To reconnect trolley, pull emergency handle straight dowm

eDO NOT PERMIT CHILDREN TO PLAY IN DOOR

AREA.

eOPERATE ONLY WHEN OPENER IS PROPERLY ADJUSTED AND THE DOOR IS VISIBLE AND UNOBSTRUCTED.

WHEN OPENER tS ACTIVATED:

1.If open, the door will close, if closed, the door will open

2.If closing, the door will reverse

3- If opening, the door wiFIstop (allowing space for entry and exit of pets and for fresh air)

4o If the door has been stopped in a partially open position, it will close.

5.If an obstruction is encountered while closing, the door will reverse.

84 If an obstruction is encountered while opening, the door will stop

7- If the optional 'infrared Sensor' is installed, the garage door will reverse in the closing cycle when the invisible beam is broken. An open door will not close when beam is broken. The sensor has no effect in the opening cycle.

OPENER LIGHT will turn on under the following conditions: when the opener is initially plugged in; when the power is interrupted; when the opener is activated. It will turn off auto- matically after 4_,_ minutes. Bulb size 75 watts maximum.

CARE OF

When properly installed, opener will l:_OVidehigh performance with a minimum of maintenance, The opener does not require additional lubrication.

Most complaints of unsatisfactory opener operation can be traced to problems with the door itself. When operated manually, a properly balanced door will stay in any point of travel while being supported entirely by its springs.

THE OPENER IS NOT INTENDED TO CORRECT ANY PROBLEMS THAT ARE CAUSED BY AN UNBALANCED OR BINDING DOOR, BROKEN DOOR SPRINGS OR BY FAULTY DOOR HARDWARE.

LIMIT AND FORCE ADJUSTMENTS: These adjustments must be checked and progedy set when opener is installed, Only a screwdriver is required. P,_ge 17 refers to the limit and force adjustments. Follow instructions carefully.

REPEAT SAFETY REVERSE TEST AFTER ANY ADUST- MENT OF FORCE AND/OR LIMITS. Weather conditions may cause'some minor changes in door operation requir- Ing some readjustments, particularly during the first year of operation.

THE SAFETY REVERSE SYSTEM IS IMPORTANT (See

Wpg,18). GARAGE DOOR MUST REVERSE ON CONTACT

ITH A ONE-INCH OBSTACLE PLACED ON THE FLOOR. FAILURE TO PROPERLY ADJUST OPENER MAY RESULT IN SERIOUS PERSONAL INJURY FROM A CLOSING GARAGE DOOR.

MAINTENANCE

AT LEAST 4 'TIMESA YEAR

MANUALLY OPERATE DOOR. If it is unbalanced or binding, call for professional garage door service.

CHECK TO BE SURE DOOR OPENS & CLOSES FULLY.

Adjust Limits and/or Force if necessary.

REPEAT SAFETY REVERSE TEST_ Make any necessary adjustments (see page 18).

THE OPENER

CHAIN TENSION ADJUSTMENT: After installation of the

opener and adjustment of forces and limits, the chain may appear loose. This is normal, To check the chain tension: disconnect the trolley by pullingthe red emergengy handle. If the chain returns to the position described and illustrated in Step 5 page 9, DO NOT make ANY further adjustmants_

TRANSMITTER: The 3-functiontransmitter willoperate more

than one garage door opener, if desired. The push buttons may also be used to operate other 53000 and/or53000SR Series devices. The standardtransmitter may be secured to car sun visor with clip provided. Additional transmitters can be purchased at any time_Refer to Accessories on page 4.

Any new transmitters must be set to the same code as the original transmitterand receiver. Page 19 explains how to

change your existing code and use the transmitter(s) with other 53000 end,or 53000SR Series receivers_ Self service

of your radio controls is not recommended. If service is needed, contactyour nearest Sears Service Center.

TRANSMITTER BATTERY: The 12 Volt battery should producepower for at least one year. As long as the battery power is adequate, the transmitter test light will glow when the push button is pressed (and the opener or other control will operate), tf light doesn'tcome on, replace the battery. If transmission range lessens, check battery test light.

TO CHANGE BATTERY: Slidethe battery compartment cover down (or remove cover screw). Position new 12Volt battery as directed.

OF YOUR OPENER

TWICE A YEAR

CHECK CHAIN TENSION. Adjust if necesseryr

ONCE A YEAR

OIL DOOR ROLLERS, BEARINGS AND HINGES.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents YoullNeed Your Opener SpecificationsInstallation Repair PartsConnect the Power Cord only to a Properly Grounded Outlet Do not USE the Force Adjustments toDo not Wear RINGS, Watches or Loose Care Serat,on of Your OpenerRequired for a garage with no DimensionsMotor 53717Youll Need Tools Carton Check ListTo Door AssemblyWhen assembled, Tee rail has a front-to-back position as Assemble Tee Rail & Attach Cable Pulley BracketAssembly Attach Tee Rail To Opener ChassisAS a Temporary STOP, Insert Screwdriver Remove Screwdriver Install Chain CableTighten Chain and CableTro Position and Instafl Header Bracket InstallationInstallation Sectional Door Installation Piece Door Without TrackAttach Tee Rail to Header Bracket Installation Sectional & ONE-PIECE Door with TrackInstallation ONE-PIECE Door With no Track N3tallationAttach Emergency Release Rope & Handle ProcedureIn.otallation Hang Opener ChassisPress and release to open or close door Install Waft Push ButtonWiring Instructions for Accessories Operation of the Wall Push ButtonNstaliation Install Light LensConnect Electric Power Permanent Wiring ConnectionInstau Door Bracket and Plate Door Installation ProcedureNstallation Sectional Door InstallationONE-PIECEDOOR Installation AdjustmentLimit Adjustment Chart AdjustmentAdjust Force AdjustUP and Down LimitsInstafl Infrared Reversing Sensor Repeat Adjustment AfterSET Receiver to Match Transmitters Code Series with Receiver Code SwitchesProbable Cause & Solution Taving a Problem? Review Pages 2 and 3 Before ProceedingRepeat Safety Reverse Test after adjustment is complete DUE to Power Failure Chain Droops or SagsNot Shown Repair PartsInstallation Parts List Trolley

139.53625SR, 139.53315SR, 139.53699SR specifications

The Craftsman garage door openers 139.53699SR, 139.53315SR, and 139.53625SR stand out in the market for their reliability, advanced features, and user-friendly design. These models are equipped with powerful motors that ensure smooth and efficient operation, making garage door opening and closing a hassle-free experience.

One of the main features of these garage door openers is their compatibility with various types of garage doors, including sectional and single-panel doors. This versatility makes them suitable for different households and garage configurations. Additionally, they offer a lifting capacity that can handle heavy doors, providing peace of mind for users with weighty garage door installations.

The Craftsman 139 series incorporates advanced technologies such as the Security+ 2.0 system. This technology enhances security by generating a new code each time the remote control is used, ensuring that unauthorized access is virtually eliminated. Furthermore, the integrated safety sensors of these openers prevent accidents by reversing the door's direction if an object is detected in its path, safeguarding both people and property.

Another notable characteristic of these models is their quiet operation. The motor design minimizes noise, making them ideal for homes with living spaces near the garage. This feature ensures that the door opens and closes without disturbing family members or neighbors, making it particularly appealing for residential use.

User convenience is a priority with the Craftsman 139 series. These openers include features such as remote control operation, allowing users to open or close their garage door from a distance. Additionally, some models come with a smartphone app integration, enabling remote access and control via mobile devices. This capability adds a layer of convenience, especially for those with busy lifestyles.

Installation of the Craftsman garage door openers is straightforward, thanks to detailed instructions and comprehensive support from the manufacturer. Many users appreciate the step-by-step guidance, making DIY installation manageable for those with basic tools and skills.

In summary, the Craftsman 139.53699SR, 139.53315SR, and 139.53625SR garage door openers are exemplary models that merge technology with functionality. They offer robust performance, enhanced security features, quiet operation, and user-friendly controls, catering to the needs of modern homeowners. Whether for new installations or upgrades, these garage door openers represent a solid choice for reliable home access solutions.
Top Page Image Contents