Craftsman 139.53675SRT owner manual Install the Premium Control Console, Serious injury or death

Page 18

• ,ll i

installation Step 6

k

Install the Premium Control Console

Locate the door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from all moving parts of the door and door hardware.

The door control is typically attached directly to the wall If installing into drywall, ddll 5/32" holes and use the anchors provided. For pro-wiredinstallations (as in new home construction), Console models may be mounted to a standard single gang box (Figure 2).

1 .Stdp 1/4" of insulation from one end of the bell wire and connect it to the two screw terminals on the back of the door control: white to 2, and white/red to 1.

2.Pry off cover along one side with a screwdriver blade (see Figure 1). Fasten with 6ABxl-1/4" self- tapping screws (standard installation) or 6-32x1" machine screws (pre-wired installation) as follows:

•Install bottom screw, allowing 1/8" to protrude above wall surface.

•Position bottom of door control on screw head and slide down to securer Adjust screw for snug fit.

•DdU and install top screw with care to avoid cracking plastic housing. Do not overtighten.

. Insert top tabs and snap on cover

3.(For standard installation) Run the bell wire up the wall and across the ceiling to the opener. Use insulated staples to secure the wire in several places. Be careful not to pierce the wire with a staple, creating a short.

4.Connect the bell wire to the terminal screws on the opener panel: white to 2; white!red to 1.

5.Position the antenna wire as shown.

Do not connect to five ele_cal _rlng. Connect only to 24 Volt low voltage wires. Connection to live wires or higher voltage may cause serious injury from shock, burn or electrocution.

Children operating or playing with a garage

door opener can Injure themselves or others. The garage door could close and cause

serious injury or death.

Install the door control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door Is Wsfble.

Do not allow ¢hIdren to operate the push button(s) or me remote control(s).

A moving garage door could.injure someone under it. Activate the opener only when the

door is properly adjusted, you can see it clearly, and there are no obstructions to door travel.

 

Hardware

Shown Actual

Size

 

 

 

 

 

Insulted

Comtol

Console (bidir,_-taJlat.i(xr_)

S_es

 

 

 

 

DryWa_,,_,ncho_

Figure

1

 

 

Figure

2

REMOVE & REPLACE

COVER

pRE-VvlRED

To Replace,

 

 

 

INSTALLATION

_._To

R_'nove,

 

 

Insert

._'_,TwisI

 

 

 

Top Tabs

*" ['P_/']r_'i

J Here

 

 

24 Volt

2-G_nductor BellWire

!

O

/

Ught

Lc_k

PREMIUM CONTROL CONSOLE

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Owners Manual Sears, Roebuck and Co, Hoffman Estates, IL 60179 U.SoAWarranty Start by Reviewing these Important Safety Alert SymbolsAssembly ElectricalYoull Need Tools To your installation Before you begin, survey your garage area toCenter of the door. See pages 12 Closed Position Carton Inventory Installation Hardware OllAssembly Section Pages 8 Right WrongHardware Shown Actual Size Fasten the T-rail to the Opener Assembly StepInstall the Trolley on the T-rail Remember to use only these screws! Any otherInstall the Chain/Cable Attach the Sprocket Cover SptImportant Installation Instructions Ghten the Chain & CableInstallation Section Pages 12 Installation Step Determine Header Bracket LocationProceed to , page t4 Proceed to , Pivot hardwareInstall the Header Bracket Fasten the Header Bracket to the WallFasten the Header Bracket to the Ceiling Installation Step Position the Opener CompletedHang the Opener Install the Premium Control Console Serious injury or deathDo not connect the power and operate Install the Lights and the LensesInstall the lenses Attach the Emergency Release Rope and HandleWiring If permanent wiring is required by your localCode, refer to the following procedure Electrical RequirementsSafety Reversing System Be sure power to the opener is disconnectedHardware Shown Atemate RoorPage Fasten Door Bracket They apply to one-piece doors also Connect Door Arm to Trolley Hole Alignment AlternativeAdjustment Procedures for One-Piece Doors Assemble the Door ArmDecrease UP limit If door does not open at least 5 feet Adjustment Section Pages 28 Adjustment StepAdjust the UP and Down Limits If the door does not close completelyProper operation of the safety reverse Adjust ForceHow and When to Adjust the Forces System. The door might not reverse properlyRepeat this test once a month and adjust as needed Test The Safety Reversing SensorImportant safety check TestInjury or death to persons MaintenanceTo reduce the risk of severe Care of Your OpenerOperation To ActivateFf you do not have a Premium Control Console Function Remote ControlFf you have a Premium Control Console Garage Door OpenerControl, but not from Probable Cause and SolutionSituation Door operates from the Door Control, but not fromHaving a Problem? Situation Probable Cause SolutionRail Assembly Parts Installation PartsRepair Parts Pner Assembly Parts 1918If you have a Premium Control Console Ff you do not have a Premium ControlConsoleIndex Call 7 am 7 pm, 7 days a week For the repair or replacement parts you need800-827=6655 Call 24 hours a day, 7 days a week

139.53675SRT specifications

The Craftsman 139.53675SRT is a versatile garage door opener designed to offer homeowners convenience, reliability, and a host of advanced features. Known for its ease of use and robust performance, this model has gained popularity in various residential settings.

One of the standout features of the Craftsman 139.53675SRT is its powerful 1/2 horsepower motor. This motor is designed to lift standard garage doors with efficiency and speed, providing a smooth opening and closing experience. Whether your door is lightweight or heavy, this opener can handle the task with minimal noise and vibration.

Incorporating advanced technology, the Craftsman 139.53675SRT features a rolling code security system. This enhances safety by changing the access code every time the remote is used, preventing unauthorized access. This technology ensures that you can trust your garage door opener to keep your home secure.

Another notable characteristic of this model is its compatibility with smartphone technology. The unit supports Smart Garage technology, allowing users to connect via their smartphones. Users can monitor and control their garage door from anywhere, adding an extra layer of convenience to everyday life.

Additionally, the Craftsman 139.53675SRT comes with a wireless keypad, which allows for keyless entry and makes it easy for family members or trusted friends to access the garage without needing to give out remotes. This keypad can be mounted outside the garage door, ensuring that anyone needing entry can do so without hassle.

Installation is made simpler with the detailed instructions provided, and the opener is designed to work with most standard garage door sizes. Additionally, the unit features a soft start and stop mechanism that reduces wear on the door and opener, extending the lifespan of both.

Safety is a priority with the Craftsman 139.53675SRT. The unit is equipped with safety sensors that detect obstructions in the door’s path, automatically reversing if anything is in the way. This feature helps to prevent accidents and injuries, particularly in households with children or pets.

In summary, the Craftsman 139.53675SRT is a reliable and feature-rich garage door opener that prioritizes convenience, safety, and technology. With its powerful motor, advanced security features, and smart connectivity, it has positioned itself as a strong contender in the market for garage door openers.
Top Page Image Contents