Frigidaire 2020215A0320, FRA103BT1 Before You Call, Occurrence Solution

Page 11

Before You Call

Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

OCCURRENCE

SOLUTION

 

 

 

 

Air conditioner will not operate.

Wall plug disconnected. Push plug firmly into wall outlet.

 

 

 

 

 

 

 

Plug Current Device Tripped. Press the RESET button.

 

 

 

 

 

 

 

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

 

 

 

 

 

 

 

Control is OFF. Turn Control ON and set to desired setting.

 

 

Air from unit does not feel cold

Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above

enough.

60°F (16°C).

 

 

 

Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.

 

 

 

 

 

 

 

Reset to a lower temperature.

 

 

 

 

 

 

 

Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to

 

 

 

restart when set in the COOL mode.

 

 

Air conditioner cooling, but room

Outdoor temperature below 60 O F (16 O C). To defrost the coil, set FAN ONLY mode.

is too warm - ice forming

 

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY

on cooling coil behind decorative

mode.

front

 

Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then,

 

 

 

 

 

 

set temperature to a higher setting.

 

 

 

Air conditioner cooling, but room

Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.

is too warm - NO ice forming on

 

Temperature is set too high. Set temperature to a lower setting.

cooling coil behind decorative

 

Air directional louvers positioned improperly. Position louvers for better air distribution.

front.

 

 

 

 

 

 

 

Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in

 

 

 

front of unit.

 

 

 

 

 

 

 

Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.

 

 

 

 

 

 

 

Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling,

 

 

 

floor and furniture.

 

 

 

Air conditioner turns on and off

Dirty air filter - air restricted. Clean air filter.

rapidly.

 

 

 

Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils

 

 

 

 

 

 

more frequently.

 

 

Noise when unit is cooling.

Air movement sound. This is normal. If too loud, set to lower FAN setting.

 

 

 

Window vibration - poor installation. Refer to installation instructions or check with installer.

 

 

Water dripping INSIDE when

Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to

unit is cooling.

installation instructions or check with installer.

 

 

Water dripping OUTSIDE when

Unit removing large quantity of moisture from humid room. This is normal during excessively humid

unit is cooling.

days.

 

 

Remote Sensing Deactivating

Remote control not located within range. Place remote control within 20 feet & 120° radius of the

Prematurely (some models).

front of the unit．

 

 

 

Remote control signal obstructed. Remove obstruction.

 

 

Room too cold.

Set temperature too low. lncrease set temperature.

 

 

 

 

 

 

 

Remote Sensing activated (on some models) and remote control located in Hot Spot - Relocate remote

 

 

 

control or deactivate remote sensing.

If These Solutions Fail, Call 1-800-944-9044 For Frigidaire Service.

2009 Electrolux Home Products, Inc.

All rights reserved.

11

 

 

 

 

 

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Use&Care Grounding type wall receptacle Important Safety InstructionsProduct Registration Record Your Model and Serial Numbers Product Registration, Packaging & Normal SoundsTo Turn Unit on YOU will see Air Conditioner Features & Operating InstructionsElectronic Control Operating Instructions To Adjust FAN SpeedsTo USE Auto FAN Feature To Operate on FAN only YOU will see To USE the Energy Saver Econ Feature YOU will seeSleep Feature YOU will see Check Filter FEATURE, YOU will see Timer Delay Stop / Start FeatureRemote Sensing Feature on some models： To Change Temperature Display YOU will seeFresh Air Vent Control Additional Things YOU should KnowCare and Cleaning Before You Call Occurrence SolutionExclusions This warranty does not cover the following Major Appliance Warranty

FRA103BT1, 2020215A0320 specifications

The Frigidaire FRA103BT1 is a cutting-edge air conditioning unit designed to provide exceptional cooling performance while maintaining energy efficiency. Featuring a sleek and compact design, this model is ideal for both residential and commercial spaces, making it a versatile choice for anyone seeking relief from the heat.

One of the standout features of the FRA103BT1 is its powerful 10,000 BTU cooling capacity, which allows it to effectively cool rooms up to 450 square feet. This makes it suitable for medium-sized rooms, ensuring that you can enjoy a comfortable environment even on the hottest days. The unit is equipped with a user-friendly, electronic control panel that includes a digital thermostat and a remote control, enabling you to adjust the temperature settings from anywhere in the room.

Energy efficiency is a significant consideration in today's market, and the Frigidaire FRA103BT1 excels in this area with an Energy Efficiency Ratio (EER) of 12.1. This means it consumes less energy while delivering powerful cooling, which can translate to lower electricity bills over time. The unit is also ENERGY STAR® certified, indicating that it meets stringent energy efficiency guidelines set by the U.S. Environmental Protection Agency.

In addition to its cooling capabilities, the FRA103BT1 features a built-in dehumidifier function, which can remove up to 3.4 pints of moisture per hour. This is especially beneficial in humid climates, as it helps maintain a comfortable indoor atmosphere without introducing excess humidity that can lead to mold and mildew growth.

The unit also offers multiple fan speeds and cooling modes, allowing users to tailor the airflow to their preferences. The convenient "Sleep Mode" adjusts the temperature automatically while you rest, ensuring a pleasant sleeping environment without the need for constant adjustments. Furthermore, the unit is designed with a washable respiratory filter that helps keep indoor air clean and free from allergens.

Installation of the FRA103BT1 is straightforward, thanks to its window-mounted design, adjustable side panels, and included installation kit. This makes it an accessible option for those who prefer a DIY approach without the need for professional assistance.

In summary, the Frigidaire FRA103BT1 is a reliable and efficient air conditioning unit that combines powerful cooling performance, energy efficiency, and user-friendly features. With its advanced technologies, this unit is a superb choice for anyone seeking comfort and climate control in their living or working space.
Top Page Image Contents