Electrolux 736684, 726682 3SHELFMODULARITY, 2CLEANINGTHECOMPARTMENT, 1PERIODICCLEANINGOFCONDENSER

C.3.3SHELFMODULARITY

To replace the shelf, remove the fixing screws located under the shelf, shift the shelf towards the front of the counter to release it from the rear seats, then lift it out.

D.1 ROUTINE MAINTENANCE

Routine maintenance tasks can be performed by non- specialized personnel. When performing maintenance, follow the instructions and pay maximum attention. The manufacturer declines any liability for damage due to incorrect use of the appliance.

WARNING:

Do not touch the equipment with wet hands or feet. Before performing any cleaning or maintenance, disconnect the equipment from the power supply and unplug the appliance. Removing the safety guards is DANGEROUS, INADVISABLE ANDUNNECESSARYforroutinemaintenance.Wearprotective gloves. Do not use scissors, screwdrivers and sharp objects on the cooling circuit.

D.1.1 CLEANING THE CABINET AND ACCESSORIES Before using the unit, clean all the inside

parts and accessories with lukewarm water and neutral soap or products that are over 90% biodegradable (in order to reduce the emission of

pollutants into the environment), then rinse and

dry carefully. Do not use solvent-based detergents (e.g. trichloro-ethylene) or abrasive powders for cleaning. Protect the metal parts with paraffin oil.

D.1.2CLEANINGTHECOMPARTMENT

To clean the compartment, remove the plug from the drain hole and let the water run into the drainage system. It is advisable to clean the compartment every week, or more frequently according to appliance use.

D.1.2 PRECAUTIONS IN CASE OF PROLONGED DISUSE During long periods of disuse, take the following precautions:

• switch the appliance off with the ON/OFF button;

• disconnect the circuit breaker ahead of the-

appliance;

• remove all food from the compartment and clean the inside

D.2 MAINTENANCE TO BE PERFORMED BY AUTHORIZED PERSONNEL ONLY

Extraordinary maintenance operations must be carried out byAUTHORIZEDSERVICEPERSONNEL.

USE SUITABLE SAFETY EQUIPMENT (GLOVESANDMASK)WHENCARRYING

OUTANY MAINTENANCEOPERATION.

WARNING:

Do not touch the equipment with wet hands or feet. Before performing any cleaning or maintenance, disconnect the equipment from the power supply and unplug the appliance. DO NOT remove the safety guards. Wear protective gloves when cleaning the condenser. Do not use scissors, screwdrivers and sharp objects on the cooling circuit.

D.2.1PERIODICCLEANINGOFCONDENSER

The condenser must be cleaned periodically, according to use, to ensure efficient operation and performance. Removing the safety guards is DANGEROUS AND INADVISABLE. It is advisable to carefully clean the cooling unit condenser openings at least once a month in dusty environments or once every three months in closed and clean places. The condenser can be cleaned with a brush, provided the bristles are not made of steel or other material that can compromise good operation, or a vacuum cleaner to remove the dust. Take maximum care not to bend the condenser fins, as this would cause a reduction in the heat exchange. Do not use sharp objects, which could damage the condenser.

NB: The condenser is installed at the top of the appliance. Do not wash the appliance with jets of water.

D.2.2 REPLACING THE POWER CABLE

To replace the power cable proceed as follows:

•Disconnect the power supply;

•Remove the electrical system guard;

•Replace the power cable;

•Refit the guard;

•Reconnect the power supply.

D.2.3 QUICK TROUBLESHOOTING GUIDE

In some cases faults can be remedied easily and quickly, by following a short troubleshooting guide:

A. The appliance does not switch on:

- make sure the plug is properly inserted in the power socket. - make sure the socket is powered.

B. The inside temperature is too high: - check the thermostat setting;

- make sure there is no heat source near the appliance; - make sure the door closes properly.

C. The appliance is excessively noisy:

- make sure the appliance is level. An unbalanced position can set off vibrations.

- make sure the appliance is not touching other equipment or parts which could reverberate;

D. The printer does not print:

and accessories;

• leave the door ajar so that air can circulate inside,

preventing the formation of unpleasant odours and mould;

• go over all the stainless-steel surfaces vigorously with a cloth

moistened with paraffin oil in order to form a protective film;

• make sure the rooms are regularly aired.

2 7

- make sure the power cable is properly connected; - make sure the printer is switched on (ON switch); - make sure parameter “E485” has the value “Prn”,

otherwise change it (to change the parameter see par. C.1.1.1 modifying user parameters)

- make sure there is paper in the printer;