Electrolux 727027, 727028, RI17RE1FU, RI93RE1FEU 6REVERSINGOPENINGOFTHEDOOR, 5ELECTRICALCONNECTION

-between top of appliance and ceiling: approx. 19.7" / 500mm:

-to the sides of appliance: approx. 3.9" / 100mm;

-for door opening: approx. 30.3" / 770 mm.

-from floor to ceiling: approx. 8.5 ft / 2610mm

Should the appliance be installed in rooms where there are corrosive substances (chlorine, etc.), it is advisable to go over all the stainless steel surfaces with a cloth coated with vaseline oil, in order to form a protective film.

These appliances are designed to operate at ambient temperatures of up to 109.4°F/+43 °C.

Note: the power plug should be accessible even after having placed the appliance in its final position for installation.

ATTENTION:

the appliance must be anchored to the floor. To anchor to the floor, drill 4 holes, as shown in the installation diagram (see letter Z), and use metal expansion plugs.

tric supply line for the appliance. It is recommended that this switch/circuit breaker have lockout/tagout capability. Before making any electrical connections to this appliance, check that the power supply is adequate for the voltage, amperage, and phase requirements on the rating plate. The customer also must provide a grounded electrical line cord of suitable capacity for the input specified on the data plate.

-After making the connection and with the appliance running, check that the rated level does not fluctuate by ± 10%.

The connection must be made with cable of a suitable for am- perage and voltage.

The manufacturer will accept no liability for any damage or injury resulting from the violation of the above rules or of the current electrical safety standards in the country where the appliance is used.

B.2.6REVERSINGOPENINGOFTHEDOOR

2 61/62"

Roll-in appliances are normally supplied with opening to the right.

3 11/32"

85 mm

75 mm

600 mm 75 mm

When changing direction of opening so that the door opens from left to right, proceed as follows:

30 5/16"

770 mm

131/32"

50 mm

34 1/4"

Z

870 mm

65 23/64"

1660 mm

24 51/64"

630mm

•disconnect from the power supply;

•unscrew the screw in the middle of the control panel, turn the control panel;

•unscrew the two fixing bolts from bracket “G” (Detail 1);

•remove the door and turn it through 180° and reverse the position of the lower seal “L” (Detail 3);

•remove component “F” and fix it in place in the space pro vided under the plastic plug on the opposite side of the door;

•remove lower bracket “E” and refit it on the opposite side in the place provided (Detail 2);

•fix bracket “G” to the structure by screwing down the fixing bolts;

•refit the door;

•adjust the lower seal “L” (Detail 3), using the slotted holes, to improve door closure;

•refit the control panel;

•reconnect the power supply.

NOTE: after anchoring the appliance to the floor, apply a sili- cone bead on the inside of the appliance between the bottom and the sides.

B.2.5ELECTRICALCONNECTION

When making the electrical connection, carefully comply with the information on the dataplate.

The appliance works on 120V/1ph/60Hz.

CAUTION:

Connection to the electrical mains must be carried out in accordance with current regulations and the standards re- quiredbytheNationalElectricCode(NEC),knownasNFPA70.

Please check:

Connection to the main power must be carried out in accord- ance with binding rules and standards.

Before connecting, make sure that:

-The line cord has an efficient grounding connection and the main power frequency corresponds to that stated on the data plate. If you have doubts on the efficiency of the grounding connection have the circuit checked by a qualified technician.

-The appliance must be connected to the main power with a permanent connection.

-In order to protect the appliance from possible overloads or short-circuits, a fused disconnect switch or a main circuit breaker (customer furnished) MUST be installed in the elec-

Detail 1

Detail 3

Detail 2

12