Electrolux 241978401 manual Automatic Ice & Water Maker/Dispenser, Priming the water supply system

Page 16

16Automatic Ice & Water Maker/Dispenser

Priming the water supply system

CAUTION

For proper dispenser operation, recommended water supply pressure should fall between 30 psi and 100 psi. Excessive pressure may cause water filter to malfunction.

1Begin filling the tank by pressing and holding a drinking glass against the water dispenser

paddle.

2Keep the glass

in this position until water comes out of the

dispenser. It may take about 1½ minutes.

3 Continue dispensing water

for about three

(3) minutes to

flush the system and plumbing connections of any impurities (stopping to empty the glass as necessary).

NOTE

The water dispenser has a built-in device that shuts off the water flow after three (3) minutes of continuous use. To reset this shutoff device, simply release the dispenser paddle.

Ice maker operation & care

After the refrigerator is installed properly and has

cooled for several hours, the ice maker can produce ice within 24 hours. It can completely fill an ice bin in about eight (8) hours.

The ice maker will produce up to nine (9) pounds of ice every 24 hours depending on usage conditions.

IMPORTANT

Your ice maker is turned on at the factory so it can work as soon as you install your refrigerator. If you cannot connect a water supply, set the ice maker’s On/Off icon to Off and turn off the water supply valve; otherwise, the ice maker’s fill valve may make a loud chattering noise when it attempts to operate without water.

Turning the ice maker on and off

“OFF”. When the ice maker is “OFF” the red LED above the icon will be illuminated.

IMPORTANT

Turning off the ice maker will result in existing ice melting in the bin.

IMPORTANT

Turning off the ice maker will disable the ice dispenser. You will still be able to dispense water.

NOTE

The ice maker also has a built-in plastic signal bale arm that automatically stops ice production when the ice bin is full. This signal arm should not be used to manually stop the ice maker.

Using the ice maker after installation

Before making ice for the first time, be sure to prime

the water supply system. Air in new plumbing lines can

result in two (2) or three (3) empty ice maker cycles. Furthermore, if the system is not flushed, the first ice cubes may be discolored or have an odd flavor.

IMPORTANT

On occasion, unusually small disc-shaped ice may be noticed in the bucket or in dispensed ice. This could occur in normal operation of the ice maker. If you start seeing these more frequently, it may be an indication of low water pressure or the water filter needs to

be replaced. As the water filter nears the end of its useful life and becomes clogged with particles, less water is delivered to the ice maker during each cycle. Remember, if it’s been six (6) months or longer since you last changed your water filter, replace the water filter with a new one. Poor quality household water may require the filter to be changed more frequently.

Ice production is controlled by the ice maker’s On/Off icon on the control panel. Press and hold the “Ice Off” icon for three (3) seconds to turn the ice maker “ON” or

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Use & Care Guide Finding Information Safety Important safety instructionsSafety Precautions DefinitionsElectrical information Feature Overview Understanding features and termsInstallation InstallationLocation Door openingTo level the cabinet using the front rollers select ModelsTo adjust the door stop To adjust the flipper mullion Removing the Doors Getting through narrow spacesTo prepare for removing the doors To remove the top hinge coversLower Hinge Removal Connecting the Water Supply To Avoid Property Damage1st Level Sleep Mode 2nd Level Awakened Display ModeControls Wave-TouchTMAlarms Setting cooling temperatures3rd Level User Variable Options Wave-TouchTMSabbath Mode Sabbath Mode and the Custom TempTM DrawerUsing the ice maker after installation Automatic Ice & Water Maker/DispenserPriming the water supply system Ice maker operation & careCleaning the ice maker Ice maker/dispenser tipsStorage Features Shelf featuresDrawers CrispersTo remove the Crisper Drawer for cleaning Special items rack select modelsDeli keeper select models Custom TempTM Drawer select modelsTo change the position of an adjustable door bin DoorsStorage bins Tall bottle retainerFreezer Features varies by model Tilt Wire ShelfDairy compartment To Remove Upper and Middle BasketsDividers Removal Ideas for storing foods Storing Food and Saving EnergyIdeas for saving energy Normal Operating Sounds Understanding the sounds you may hearChanging The Water and Air Filters Water filterAbout your advanced water filter Replacing your PureAdvantageTM water filterAir filter Ordering replacement filtersReplacing your PureAdvantageTM air filter Care and Cleaning Protecting your investmentCare and cleaning tips Part Cleaning Agents Tips and PrecautionsVacation and moving tips Occasion TipsOrdering Replacement LED Lights Replacing LED Lights select modelsReplacing Light Bulbs select models To replace LED LightsProblem Cause Correction Solutions to Common ProblemsBefore you call Light Is Not On Temperatures Are Too Cold Water Dispenser Warranty Consumer
Top Page Image Contents