Electrolux ESL 4115 Prior to using for the first time, Water softener, Setting manually

Page 6

Prior to using for the first time

Before using your dishwasher for the first time:

1.Ensure that the electrical and water connections comply with the installation instructions

2.Remove all packaging from inside the appliance

3.Set the water softener

4.Pour 1 litre of water inside the salt container and then fill with dishwasher salt

5.Fill the rinse aid dispenser

The water softener

The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance.

The higher the content of these minerals and salts, the harder your water is.

Water hardness is measured in equivalent scales, Clarke degrees, French degrees (°TH) and mmol/l (millimol per litre - international unit for the hardness of water).

The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area.

The water softener must be set in both ways: manually, using the water hardness dial and electronically, by the means of the programme selection/cancel button.

a) Setting manually

1.Open the dishwasher door.

2.Remove the lower basket from the dishwasher.

3. Turn the water hardness dial to position 1 or 2 (see table).

4.Replace the lower basket.

b) Setting electronically

The dishwasher is factory set at level 5.

1. With the dishwasher switched off, press the On/Off button.

The end of cycle indicator light flashes (setting mode).

In case salt and/or rinse aid refilling is necessary the

corresponding indicator lights illuminate.

If one of the washing programme indicator lights is on, this

means that a washing programme has been set.

The setting must be cancelled: press for about 3 seconds

the programme selection/cancel button; the indicator

light of the set programme turns off and the end of cycle

indicator light flashes, indicating that the set programme

has been cancelled and that the machine is now in setting

mode.

2. Press and keep pressed the programme selection/cancel

button until the programme indicator light 1 turns on and

programme indicator light 2 flashes, indicating that you have

activated the water softener setting function.

After a few seconds the end of cycle indicator light starts

flashing.

The current level is indicated by a sequence of flashes of

the end of cycle indicator light, a sequence of intermittent

audible signals and a pause of a few seconds (see chart).

Example: 5 flashes/5 audible signals + pause +

5 flashes/5 audible signals etc...= level 5

3. To change the level, press the programme

selection/cancel button.

Each time the button is pressed the level changes. (For the

selection of the new level, see chart).

Examples:

if the current level is 5, by pressing the programme

selection/cancel button once, level 6 is selected.

The dishwasher is factory set at position 2.

AA07

if the current level is 10, by pressing the programme

selection/cancel button once, level 1 is selected.

The end of cycle indicator light remains off for a few

seconds and then starts flashing indicating the new

selection is set.

5.To memorise the operation, switch off the machine by pressing the On/Off button or wait for about 60 seconds, after which the machine will automatically return to setting mode.

 

Water hardness

 

Adjusting the

Number of flashes of

Use of

 

 

 

 

water hardness

the "end of cycle"

salt

Clarke

°TH

mmol/l

Range

setting

indicator light and of

 

 

 

 

 

 

 

 

 

 

 

 

audible signals

 

 

 

 

 

manually

electronically

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

64 - 88

91 - 125

9,0 - 12,5

IV

2

level 10

10

yes

 

 

 

 

 

 

 

 

53 - 63

76 - 90

7,6- 8,9

IV

2

level 9

9

yes

 

 

 

 

 

 

 

 

46 - 52

65 - 75

6,5 - 7,5

IV

2

level 8

8

yes

 

 

 

 

 

 

 

 

36 - 45

51 - 64

5,1 - 6,4

IV

2

level 7

7

yes

 

 

 

 

 

 

 

 

28 - 35

40 - 50

4,0 - 5,0

IV

2

level 6

6

yes

 

 

 

 

 

 

 

 

23 - 27

33 - 39

3,3 - 3,9

III

2

level 5

5

yes

 

 

 

 

 

 

 

 

18 - 22

26 - 32

2,6 - 3,2

III

1

level 4

4

yes

 

 

 

 

 

 

 

 

13 - 17

19 - 25

1,9 - 2,5

II

1

level 3

3

yes

 

 

 

 

 

 

 

 

5 - 12

7 - 18

0,7 - 1,8

I/II

1

level 2

2

yes

 

 

 

 

 

 

 

 

< 5

< 7

< 0,7

I

1

level 1

1

no

 

 

 

 

 

 

 

 

6

Image 6
Contents S h w a s h e r Contents Child safety Safety instructionsInstallation DisposalDescription of the appliance Audible signals Deactivation/activation of the audible signalsControl panel Prior to using for the first time Setting manuallyWater softener Rinse aid Adjusting the doseFilling with dishwasher salt Filling with rinse aidLower basket Daily useLoading cutlery and dishes Cutlery basketUse of detergent Adjusting the height of the upper basketUpper basket To move to the higher position proceed as followsConcentrated detergent Different kinds of detergentDetergent tablets Combi detergentsWashing programmes Starting a washing programme To interrupt or cancel a washing programme in progressCancel a washing programme in progress Unloading the dishwasherFrost precautions Maintenance and cleaningCleaning the filters Prolonged periods of non-operationFault code / malfunction Possible cause Solutions Fault code appearsThere are problems when operating the dishwasher Malfunction Possible cause SolutionsDishes are wet and dull Dishes are not cleanWash results are not satisfactory Water drops have dried onto glasses and dishesService and Spare Parts Customer Care DepartmentEuropean Guarantee Guarantee ConditionsStandard Guarantee Conditions ExclusionsLevelling Installation instructionsBuilding-in Fixing to the adjacent unitsGreen and Yellow Earth Blue- Neutral Brown- Live Water outlet hose connectionElectrical connection Proceed as followsHints for test centres Cup racks position aPage Page Page Electrolux plc