Electrolux GXWDOEOOOO Automatic Control, Setting the clock, Starting, Switching on, Shutting down

OPERATING INSTRUCTIONS

150 LT 15 50 28

4.AUTOMATIC CONTROL

The automatic controls can be fitted with more or fewer func- tions.

The following instructions explain all the possible functions.

4.1Setting the clock

The clock time is shown on the display (AZ).

Switch on the control system switch (S) by turning them from position 0 to I.

Then press and hold down buttons (ZT) and (Q). After the second acoustic signal, the clock time can be set by turning the knob (Z).

Turn right = increase Turn left = reduction Smallest change = 1 minute

After the time has been set, the buttons (ZT) and (Q) can be released again.

4.2Starting

The pan must be in the horizontal position prior to starting, or the power supply must be disconnected.

Programming the cooking time, the starting time and steam condensation in the compartment (or only one func- tion). The starting-time programme only exists as an option.

Pressing the button (DT) switches on the programme for the cooking time (flashing nominal value). The desired cooking time is set with the cooking time knob (D) on the display (AD).

Turn right = increase Turn left = reduction Smallest change = 1 minute

The lamp (LD) only lights up when the desired temperature has been reached and the cooking time expires.

Pressing the button (ZT) switches on the programme for the starting point (flashing nominal value).

Set the desired starting time with the starting time knob (Z) on the display (AZ)

Turn right = increase Turn left = reduction Smallest change = 1 minute

The acoustic signal will sound three times and the lamp (LZ) will light up when the starting time has been reached.

Steam condensation (optional) is pre-programmed by press- ing button (V).

4.3Automatic cooking

TT Button, activation of settings

LT	Lamp, cooking temperature
DT	Button, cooking time
LD	Lamp, cooking time expires
ZT	Button, starting time
LZ	Lamp, starting time
LR	Lamp, soft settings

QButton, acoustic signal

RButton, soft

LS Lamp, temperature pre-setting

AT Display, cooking tempera- ture

TTemperature selection knob AD Display, remaining cooking

time

D Cooking time knob AZ Display, time

Z Starting time knob S Control switch

Fig. 2 Right console

Switching on

Switch on the control switch (S) turn from position 0 to I. This switches on the temperature pre-setting function. The lamp (LS) lights up.

0 = Off

I = On

Set the desired cooking temperature (flashing nominal value) with the temperature selection knob (T) on the display (AT).

Turn right = increase Turn left = reduction Smallest change = 1°F

The following pre-programmed nominal functions

•Cooking temperature

•Cooking time

•Starting time

•Steam condensation

are all activated by pressing the button (TT). The following displays

•Cooking temperature (AT)

•Remaining cooking time (AD)

•Clock time (AZ)

indicate the current value.

The lamp (LT) will continue to flash until the nominal cooking temperature is reached. It then stays on permanently.

When illuminated, this lamp (LV) indicates that steam conden- sation is switched on. When cooking is completed, steam con- densation will start automatically and will remain in operation until the pressure in the appliance has been reduced to nor- mal. The lamp (LV) will flash during the cooling phase.

4.4Shutting down

An acoustic signal sounds when cooking is over. This is acknowledged by pressing the button (Q).

The power supply is then switched off.

All activated functions are subsequently switched off:

•Press the pre-set temperature button (TT) for some sec- onds.

Lamp (LT) extinguishes.

•Press the cooking time button (DT). Lamp (LD) extinguishes.

•Press the starting time button (ZT). Lamp (LZ) extinguishes.

(Starting-time programme exists as an option)

•Press the button for steam condensation (V). The lamp (LV) will extinguish.

•Switch off the Soft button (R), if this was activated.

•Switch off the control switch (S). Turn from position I to 0.

Lamp (LS) extinguishes.

•Switch off the power isolator (H) (only available as an option).

•Turn from position I to 0.

0 = Off

After cooking has been completed, the control switch (S) is switched off.

Page 6 62.9696.01