Front View

Use the POWER switch located in the centre of the front panel to switch the appliance’s power on. The soft-start function prevents current inrush peaks on the mains, which in addition prevents the mains line protection switch from activating during power-on operation of the power amplifier. The loudspeaker outputs are activated via relay switching with a delay of approximately 2 seconds effectively attenuating eventual power-on noise. The PROTECT LED lights during the delay time and the fans run at maximum speed. This is normal to confirm the immaculate operation of the protection circuitry. Upon power-on, all power amps with RCM-24 Module installed regain the state of operation prior to the last power-off.

For example: if a power amplifier had been switched off using the POWER-switch while being in Stand- by mode, upon power-on it restarts in this exact mode.

This indicator lights when the power amplifier has been switched on. Causes for the POWER-indicator not lighting are: the appliance is not connected to the mains network, a defective primary fuse, or the power amplifier is set to stand-by operation (STAND-BY LED lights).

This indicator light when the power amplifier is in stand-by mode, which can be activated from the RCM-24 or via Easy Remote. In stand-by operation only the internal auxiliary power supply unit is activated. The main power supply unit is separated from the mains.

The PROTECT LED lights indicating that one of the internal protection circuits against thermal overload, short-circuit, Back-EMF, HF-occurrence at the output, etc., has been activated. In that case, the output relays separate the power amps from the load connected to prevent the connected loudspeaker systems and the power amplifiers as well from being damaged. Whatever caused the fault – e.g. a short- circuited speaker cable – needs to be remedied. In case of thermal overload you have to wait until the power amplifier automatically regains normal operation

The OUT LED lights as soon as an audio signal of approximately 30dB below full modulation is present. The LED is dimmed when speaker cables are short-circuited or a protection circuit has been activated

The 0dB LED lights when the power amplifier is driven at its maximum. Higher input voltage does not result in higher peak output voltage.

This indicator lights as soon as the integrated dynamic limiter is activated and the power amplifier is driven at the clipping limit or generally at its maximum capacity. Short-term blinking is not a problem, since the internal limiter trims input levels of up to +21dBu down to a S/N-ratio of approximately 1%. If, on the other hand, this LED lights constantly, reducing the volume is recommended to prevent the loudspeaker systems connected from being damaged by probable overload

P1200RL, P900RL specifications

Electro-Voice P900RL and P1200RL are high-performance power amplifiers designed for various audio applications, including live sound reinforcement, installations, and studio settings. These amplifiers stand out in the market due to their innovative technologies and robust features, making them suitable for both professional audio engineers and audio enthusiasts.

The P900RL model delivers a powerful 900 watts per channel at 4 ohms, while the P1200RL offers an even more impressive output of 1200 watts per channel at the same impedance. This significant power enables these amplifiers to drive a wide range of loudspeakers proficiently, ensuring clean and dynamic sound reproduction with minimal distortion.

One of the key features of the P900RL and P1200RL is their efficient Class H topology. This technology improves energy efficiency by maintaining high power output with less heat. Class H amplifiers dynamically adjust their power supply voltage according to the input signal, resulting in reduced power consumption and increased longevity of the components. This makes the P series amplifiers not only powerful but also environmentally friendly.

Both models come equipped with a built-in limiter and comprehensive protection circuitry to prevent damage from overheating, short circuits, and overloading, ensuring safety and reliability in demanding environments. Additionally, the amplifiers feature a tri-mode operation, enabling them to be configured for stereo, parallel, or bridged mono setups, providing versatility for various audio applications.

The P900RL and P1200RL also include advanced signal processing capabilities, including a variable low pass filter for enhanced sound control and clarity. The integrated cooling system maintains optimal operating temperatures, allowing for extended use without the risk of thermal issues.

Audio connectivity is straightforward with both XLR and ¼-inch TRS inputs, allowing the amplifiers to interface with a variety of audio sources. The professional-grade output connectors ensure secure and reliable connections to speakers, critical for live sound applications.

In conclusion, the Electro-Voice P900RL and P1200RL amplifiers offer a compelling combination of power, efficiency, and versatility. With their advanced technologies and protective features, they cater to the demanding needs of sound professionals while delivering high-quality audio performance suitable for any occasion.