Electrolux E39WD75GTT Panel-Ready Warmer Drawer Specifications, Custom Panel Specifications

Warmer Drawer

E30WD75GTT panel ready

Note: Refer to web for detailed custom

panel construction and installation instructions.

23 3/8" (not including

custom panel)

Mounting panel

29"
Overall depth with	10 3/4"
drawer fully extended
(excluding custom panel
and handle) – 41 1/2"

Panel-Ready
Warmer Drawer
			9 7/8" min.
Stand-Alone			10 1/4"max.
Installation			4 1/2" min.	28 1/2" min.	23 5/8"min.
Power cord				28 3/4" max.	24"max.
			required
location (right			distance
center rear)			to floor
					Full plywood
					base required to
7/8"					support 100 lbs.
		Custom
	Panel Specifications			Custom
				panel
	Height	Width	Thickness	Mounting
111/4"		30"	1/2"min.	panel

30" Panel-Ready Warmer Drawer Specifications

•Product Weight – 41 Lbs.

•Voltage Rating – 120V/450W/60 Hz/15 Amps

•Connected Load (kW Rating) @120 Volts = 0.45kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)

•Amps @120V = 3.75 Amps

•Full plywood base required, capable of supporting 100 Lbs.

•Base must be level and cabinet front must be square.

•Warmer Drawer can be used alone, or is approved to be used in combination with any Electrolux ICON™ Wall Oven. (Refer to Combination Installation Specifications and drawing on this page.)

•Warmer Drawer can be used alone, or is approved to be used in combination with any Electrolux ICON™ built-in product. (Refer to Combination Installation Specifications pages on web.)

Custom Panel Specifications

•Handle not included, match to custom cabinetry.

•Panel Dimensions – 11-1/4"H x 30"W x1/2"min. D

•Refer to web for detailed custom panel construction and installation instructions.

Optional Accessories

•ServeWare – (5304447729).

Warmer Drawer / Single Wall Oven	1	1
		/2"
Combination Installation	min.

28 1/2"

min.

28 7/8"

max.

1	3
	/4"
	†
min.

28 1/2"min.	24"*
	(critical
28 3/4"max.	dimension)
30" min.

4" x 4" opening to route armoured cable

Bottom of oven cutout

		*Critical dimension –
11	5/8"	MUST be applied
		**Electrical junction
min.*
		box for Wall Oven

Custom front panel with custom handle (not included)

9 7/8" min.

10 1/4"max.

Two 3" wide x 3/4" thick planks must be installed, capable of supporting 200 lbs.

Electrical junction box location

	must be lower than
	the Warmer Drawer
	cutout
	†
	Maximum height
	depends on critical
5
	dimension (11 /8")
3"
max.**

Warmer Drawer/Wall Oven Combination Specifications

•To support Wall Oven when using in combination with Warmer Drawer, two 3"-wide x 3/4" thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement.

Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.

USA • 250 Bobby Jones Expressway • Augusta, GA 30907 • 1-877-4electrolux (1-877-435-3287) • electroluxicon.com	High standards of quality at Electrolux Home Products, Inc. mean we are
	constantly working to improve our products. We reserve the right to change
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxicon.ca
	specifications or discontinue models without notice.

E30WD75GTT 03/08 © 2008 Electrolux Home Products, Inc. Printed in the U.S.A.