KitchenAid 9763393A Venting Requirements, Product Dimensions, Installation Clearances

Product Dimensions

30" (76.2 cm) model: 8" (20.3 cm)

36" (91.4 cm) model: 11" (27.9 cm)

FRONT OF

30" (76.2 cm) model: 26" (66.0 cm)

36" (91.4 cm) model: 32" (81.3 cm)

4³⁄₈"	3¹⁄₄" (8.3 cm)
(11.1 cm)

VENT HOOD10" (25.4 cm)

	2³⁄₈"
	(6.0 cm)	2"
9¹⁄₂"
		(5.1 cm)
(24.1 cm)
	8"	¹⁄₄"
Shelf extends	(20.3 cm)	(6.4 mm)
7" (17.8 cm)
	1⁵⁄₈"	1¹⁄₄"
		(31.8 mm)
1"	(41.3 mm)
(25.4 mm)		⁵⁄₈" to 2¹⁄₈"
		(1.6 cm to 5.4 cm)

9¹⁄₈"

11" (23.2 cm) (27.9 cm)

2"

(5.1 cm)

³⁄₈" (9.5 mm)

30" (76.2 cm) model: 13" (33.0 cm)

36" (91.4 cm) model: 16" (40.6 cm)

BACK OF

VENT HOOD

30" (76.2 cm) model: 29⁷⁄₈" (75.9 cm)

36" (91.4 cm) model: 35⁷⁄₈" (91.1 cm)

1⁷⁄₁₆"

(3.6 cm)

Installation Clearances

Venting Requirements

30" (76.2 cm) or 36" (91.4 cm) min. cabinet opening width

24" (61 cm) min.

30" (76.2 cm) suggested max. bottom of cabinet to cooking surface

66"(167.6 cm) min.

■ Vent system must terminate to the outside, except for non-

vented (recirculating) installations.

■ Do not terminate the vent system in an attic or other enclosed

area.

■ Do not use a 4" (10.2 cm) laundry-type wall caps.

■ Use a metal vent only. A rigid metal vent is recommended. Do

not use plastic or metal foil vent.

■ The size of the vent should be uniform.

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than one elbow is used.

15" (38.1 cm) min. clearance upper cabinet to countertop

13" (33 cm) cabinet depth

72" (182.9 cm) max.

to bottom of cabinet frame

■ Do not install 2 elbows together.

■ The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

■ The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

■ Use clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around the

cap.

36" (91.4 cm) base cabinet height

■ Determine which venting method is best for your application.

Cold weather installations

An additional back draft damper should be installed to minimize backward cold air flow and a nonmetallic thermal break should be installed to minimize conduction of outside temperatures as part of the vent system. The damper should be on the cold air side of the thermal break.

The break should be as close as possible to where the vent system enters the heated portion of the house.

5