KitchenAid KHTU100 installation instructions Now start

Page 4

Now start...

1.Put a thick protective covering over cooktop, set-in range or countertop to protect from damage or dirt.

If installing over a freestanding range, disconnect and move the range to provide easier access to the upper cabinet and rear wall.

Slide range onto cardboard or hardboard before moving to prevent damaging floor covering.

2.Place hood on a protective cover with filters facing down.

3.Determine which venting method (roof, wall or non-vented) will be used.

•The hood is factory-set for roof venting.

•For non-vented installations, go to Step 4.

seal plate

vent connection

If venting through the wall, remove seal plate from back of hood and vent connector from top of hood. Reinstall vent connector onback of hood and seal plate on top of hood.

top

knockout

do not use

centerlines

5.Mark centerlines on rear wall and upper cabinet bottom.

For non-vented installations: Extend centerline up onto soffit above hood.

template

6.Align centerlines of template with centerlines marked on rear wall and upper cabinet bottom. Tape template in place. Mark location of the four holes used to secure hood to upper cabinet.

7.Depending on your installation, mark location of the wiring hole or vent cutout in upper cabinet or back wall needed as shown on template.

8.Remove template.

9.Drill four 3/16" (5.0 mm) diameter holes through upper cabinet for the hood mounting screws.

10.Drill the 1-1/2" (4.0 cm) wiring hole.

11.Make the vent cutout for

3-1/4" x 10" (8.3 x 25.4 cm) rectangular vent system. Note: It is recommended that vent system be installed before installing hood.

12.Turn the hood over so

13.Rotate deflector away from filters. Pull grease filter handles toward back of hood to release locking tabs. Lift filters up, remove from hood and set aside.

screw locations

screw

14.Remove 2 screws from light panel tabs. On light panel surface directly behind tabs, push toward back of the hood to move tabs out through the slots. Remove panel and set aside with screws.

remove screws

wiring

box cover

15.Remove 2 screws from wiring box cover located in the right hand rear corner and remove cover. Attach the U.L.- or CSA-

back knockout

these

knockouts

filters face up.

listed strain relief to the hood wiring hole being used.

4.Remove knockout from the wiring opening (top or back) to be used.

4

16.Turn hood over so filters face down.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Table of Contents Quick ReferenceInstaller It is the customer’s responsibilityTo assure that the electrical Conformance with NationalProduct dimensions Wall venting4 x 10 8.3 cm x 25 cm Vent system Maximum length = 26 ft mNow start Electrical connection Non-vented installations InstallNon-vented recirculating Wiring diagram Use and Care InformationOperation of range hood To turn fan on and OFFWarranty Replacing lightsRequesting Assistance or Service Our consultants provide assistance withIf you need service 830 a.m. 6 p.m. ESTPage Consultation rapide Table des matièresContacter un électricien qualifié pour l’installation Avant de commencer…Décharge à Travers le mur Circuit d’évacuation en conduit de X 25 cm 3 1/4 x 10 poLongueur maximale = 8 m Décharge à Travers le toitCommencer maintenant Avertissement Raccordement au circuit électriqueUtilisation et entretien Utilisation de la hotteGarantie Demande dassistance ou de service Nos consultants fournissent de l’assistance pourSi vous avez besoin dassistance au de service au Canada 2001

KHTU100 specifications

The KitchenAid KHTU100 is a powerful and versatile kitchen appliance designed to elevate your cooking experience. Known for its robust construction and user-friendly features, this unit is perfect for home chefs seeking efficiency and convenience.

One of the standout features of the KHTU100 is its powerful heating element that ensures consistent and precise temperature control. Whether you're sautéing vegetables, simmering sauces, or slow-cooking hearty stews, this appliance delivers even heat distribution for optimal results every time.

Equipped with a large capacity, the KHTU100 is designed to accommodate various dishes. Its spacious interior allows you to prepare meals for the entire family, making it an excellent choice for gatherings and special occasions. The non-stick coating ensures easy cleanup and reduces the risk of food sticking, allowing you to focus more on cooking and less on scrubbing.

The KHTU100 comes with multiple cooking modes, including steaming, slow cooking, and reheating, which cater to a wide range of cooking preferences. This multi-functionality means that you can experiment with different cooking techniques without needing multiple appliances cluttering your kitchen. The intuitive control panel makes it easy to select the desired function, temperature, and cooking time.

Another notable technology in the KHTU100 is its built-in safety features. It includes an automatic shut-off function that activates after a predetermined time, providing peace of mind when you're busy with other tasks in the kitchen. This is particularly beneficial for busy families or anyone who often multitasks while cooking.

The sleek design of the KitchenAid KHTU100 not only makes it aesthetically pleasing but also functional. The compact size allows it to fit neatly on your countertop without occupying too much space. The stylish exterior is available in several colors, ensuring that it will complement any kitchen decor.

In summary, the KitchenAid KHTU100 is a versatile and reliable kitchen appliance that combines power, efficiency, and safety. With its multiple cooking modes, easy-to-clean surfaces, and appealing design, it's an excellent addition to any kitchen. Whether you are a novice or an experienced chef, the KHTU100 is poised to enhance your culinary adventures.
Top Page Image Contents