KitchenAid 9752043 installation instructions Before you start, Mobile home installation, Panel a

Before you start...

Your safety and the safety of others

are very important.

We have provided many important safety messages in this manual and on your appliance.

Cabinet opening dimensions

25" (63.5 cm) countertop depth and 24" (61 cm) base cabinet depth, 36” (91.4 cm) countertop height

Freestanding Range Slide-in Range

Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING”. These words mean:

DANGER

You can be killed or seriously injured if you don’t immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

18" (45.7 cm) upper cabinet to countertop

4" (10.2 cm) min. clearance from both sides of range to side wall or other combustible material.

		For minimum
	13" (33 cm) max.	clearance to
upper cabinet depth		the top of the
		cooktop, see
	30" (76.2 cm) min.	Note.***
	cabinet opening width

		18" (45.7 cm)
		upper cabinet
		to countertop
30-1/4" (76.8 cm)
opening width
		4" (10.2 cm)
		min. clearance
		from both sides
		of range to side
	junction box –
		wall or other
	8" (20.3 cm) to
		combustible
	22" (55.9 cm) from
		material.
	either cabinet,
	7" (17.8 cm) max.
	from floor.
7/8" (2.2 cm)
min. required
between cutout
and cabinet
door or hinge.

13" (33 cm) max.			For minimum
upper cabinet depth			clearance to
			the top of the
	30" (76.2 cm) min.
			cooktop, see
	cabinet opening width
			Note.***
		22-3/4" (57.8 cm)
		opening depth

1/2" (1.3 cm) radius both corners

30-3/8" (77.2 cm) opening width

junction box – 8" (20.3 cm) to 22" (55.9 cm) from either cabinet, 7" (17.8 cm) max. from floor.

7/8" (2.2 cm) min. required between cutout and cabinet door or hinge.

Read electrical and carpentry instructions.

Proper installation is your responsibility. A qualified technician must install this range. Make sure you have everything necessary for correct installation. It is the customer’s responsibility to make sure that the countertop has been properly prepared and that the installation clearances specified on the model/serial rating plate are met. The model/serial rating plate is located on the oven frame behind the drawer.

Check location where range will be installed. The range should be located for convenient use in the kitchen. Recessed installations must provide complete enclosure of the sides and rear of range.

ALL OPENINGS IN THE WALL OR FLOOR WHERE RANGE IS TO BE INSTALLED MUST

Important: Observe all governing codes and ordinances.

When installing a range under existing cabinets and the installation does not meet the minimum cabinet clearances, install a range hood above the cooktop to avoid burn hazards.

Grounded electrical outlet is required. See “Electrical requirements,” Panel B.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

Do Not pinch the power supply cord between the range and the wall.

Do Not seal range to side cabinets.

***Note: 24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than 1/4" (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

30" (76.2 cm) min. clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.

Anti-tip bracket:

The floor anti-tip bracket MUST be installed. To install the anti-tip bracket shipped with the range, see Panel C and the anti-tip bracket template.

BE SEALED.

IMPORTANT: Some cabinet and building

Slide-in ranges: countertop preparation

materials are not designed to withstand the heat produced by the oven for baking and self- cleaning. Check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

It is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is adiquate and in conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standard C22.1, Canadian

The cooktop sides of the slide-in range fit over the cutout edge of your countertop.

If you have a square finish (flat) countertop and the opening width is 30-3/8" (77.2 cm), no countertop preparation is required.

Formed front-edged countertops: Must have molded edge shaved flat 1/4" (0.64 cm) from each front corner of opening.

Tile countertops may need trim cut back 1/4" (0.64 cm) from each front corner and/or rounded edge flattened.

If countertop opening width is greater than 30-3/8" (77.2 cm), adjust the 1/4" (0.64 cm) dimension.

Countertop must be level. Place level on countertop, first side to side; then front to back. If countertop is not level, range will not be level. Oven must be level for satisfactory baking conditions.

Electrical Code, Part 1 — latest edition**, and all local codes and ordinances.

Note: The metal chassis of the range MUST be grounded in order for the control panel to work. If the metal chassis of the range is not grounded, NO keypads will operate. Check with a qualified electrician if you are in doubt as to whether the metal chassis of range is grounded.

Mobile home installation

The installation of this range must conform to the Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly the

30-3/8"
(77.2 cm)
opening	1/4"
width	(0.64 cm)	22-5/8"
		(57.5 cm)
30-7/8"	Formed or tiled countertop
(78.4 cm)	trimmed 1/4" (0.64 cm)
	back at front corners of
	countertop opening.	Cooktop sides of range fit over
		edges of countertop opening.
Product dimensions
Freestanding Range		Slide-in Range

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280); or when such standard is not applicable, the Standard for Manufactured Homes Installations (Manufactured Home Sites, Communities and Setups), ANSI A225.1/NFPA 501A, or with local codes*.

In Canada, the installation of this range must conform with the current standards CAN/CSA-Z240 — latest edition**, or with local codes.

When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

Four-wire power supply cable must be used in a mobile home installation. The appliance wiring will need to be revised. See four-wire electrical connection, Panel B.

Copies of the standards listed may be obtained from:

*National Fire Protection Association One Batterymarch Park

Quincy, Massachusetts 02269

**Canadian Standard Association 178 Rexdale Boulevard

Rexdale (Toronto), Ontario M9W 1R3

Panel A

	30"
8-1/4"	(76.2 cm)
(21 cm)	cooktop
	width

1" (2.5 cm) spacer

27-3/4"

(70.5 cm)

depth with

handle

							30"
							(76.2 cm)
							cooktop
			1-1/2"
							width
			(3.8 cm)
	44-3/8"
	(112.7 cm)
	overall
	height
		36" (91.4 cm)
						22-5/8"
		cooktop
		height with				(57.5 cm)
		feet loosened
		1-1/2 turns
36" (91.4 cm)
cooktop
height with				1"
feet loosened				(2.5	cm)
1-1/2 turns

30"
(76.2 cm)		25-3/4"
width	When installed in a 24"	(65.4 cm)
		depth with
	(61 cm) base cabinet with
		handle
	25" (63.5 cm) countertop —

front of oven door protrudes 1-7/8" (4.8 cm) beyond 24" (61 cm) base cabinet.

30"

(76.2 cm)

width