KitchenAid KUDI01DL manual Dishwasher Efficiency Tips, Rinse Aid Dispenser

Water Hardness	Amount of Detergent
Medium to Hard	For normal and heavily
Water	soiled loads
7 to 12 grains per	■ Partially fill the Main Wash
gallon	section (7 tsp or 35 g)
	■ Fill the Pre-Wash section
	(4 tsp or 20 g)

set the adjuster to 1 or 2. If there are rings or calcium (hard water) spots on dishes, try a higher setting.

To adjust the setting

Very Hard Water

13 grains per gallon and above

NOTE: It might be necessary to use the Heavy cycle, or a normal cycle with Hi-Temp Scrub, for best wash performance with very hard water.

For normally and heavily soiled loads

■Fill the Main Wash section (8 tsp or 40 g)

■Fill the Pre-Wash section (4 tsp or 20 g)

■Turn the rinse aid dispenser to a higher setting. See “Rinse Aid Dispenser” later in this section.

Open the dispenser cover. Turn the adjuster inside the dispenser to the desired setting.

Dishwasher Efficiency Tips

Hot water dissolves and activates the dishwashing detergent. Hot water also dissolves grease on dishes and helps glasses dry spot-free. Is the water temperature too low? For best dishwashing results, water should be 120°F (49°C) as it enters the dishwasher. Loads may not wash as well if the water temperature is too low. Water that is too hot can make some soils harder to remove and cause certain detergent ingredients not to function. If your water heater is located far from the dishwasher, it

NOTE: Fill amounts shown are for standard powdered detergent. Amounts may vary if you use liquid or concentrated powdered detergent. Follow instructions on the package when using liquid dishwasher detergent or concentrated powdered detergent.

Rinse Aid Dispenser

Rinse aids prevent water from forming droplets that can dry as spots or streaks. They also improve drying by allowing water to drain off of the dishes during the final rinse by releasing a small amount of the rinse aid into the rinse water. Your dishwasher is designed to use a liquid rinse aid. Do not use a solid or bar-type.

may be necessary to run the hot water at the faucet closest to the dishwasher to minimize the amount of cold water in the water line.

To check water temperature

1.Run hot water at the faucet closest to your dishwasher for at least 1 minute.

2.Place a candy or meat thermometer in a glass measuring cup.

Filling the dispenser

The rinse aid dispenser holds 4.8 oz (145 mL) of rinse aid. Under normal conditions, this will last for about three months. Rinse aid is released through an opening in the dispenser. When latched properly, the cover remains closed. The cover should be opened only when refilling the dispenser. You do not have to wait until the dispenser is empty to refill it. Try to keep it full, but be careful not to overfill it.

1.Make sure the dishwasher door is fully open.

2.Open the dispenser by pushing the cover latch.

1

3

2

1.Cover latch

2.Rinse aid dispenser

3.Indicator window

3.Add rinse aid until the indicator window looks full.

4.Clean up any spilled rinse aid with a damp cloth.

5.Close the cover.

NOTE: The cover latch clicks when the cover is closed and latched.

Rinse aid setting

The amount of rinse aid released into the final wash can be adjusted. The factory setting is at 2. For most water conditions,

3.Check the temperature on the thermometer as the water is running into the cup.

■To save water, energy and time, do not rinse dishes before putting them into the dishwasher.

■Use the Normal cycle whenever possible. This cycle uses less hot water and energy than other cycles.

■Use a delay feature (on some models) to run your dishwasher during off-peak hours. Local utilities recommend avoiding heavy usage of energy at certain times of day.

■During the summer, run your dishwasher at night. This reduces daytime heat buildup in the kitchen.

■Use an air dry, or an energy-saving dry option whenever possible. Allow longer drying times (overnight) when using these options. Use a rinse aid to improve drying.

■Use cycles or options that add extra heat to the wash or rinse portion of the cycle only when needed.

■Run your dishwasher with full loads. Run a rinse cycle after meals until the dishwasher is full.

■If your home is equipped with a water softener, you may want to avoid starting the dishwasher during the regeneration of the softener, as this may contribute to poor wash performance.

10