KitchenAid 9759405C Installation Requirements, Toolsand Parts, Location Requirements

Page 4

INSTALLATION REQUIREMENTS

Toolsand Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed

Adjustable wrench

¹⁵⁄₁₆" combination wrench

Tape measure

Wrench or pliers

Marker or pencil

Pipe-joint compound

Pipe wrench

 

resistant to LP gas

 

Noncorrosive leak-

Flat-blade screwdriver

 

detection solution

 

 

 

Parts Supplied

Check that all parts are included.

Gas pressure regulator

Burner grates

Burner caps

Simmer plate

Grill grate (on some models)

Drip tray (on some models)

Front spill guard (on some models)

Wave tray (on some models)

Wave plate (on some models)

Backguard

Island trim

Parts Needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop burner box.

It is recommended that an overhead vent hood be used with this cooktop. For island installations, a 48" (122 cm) hood is recommended.

The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.

All openings in the wall or floor where cooktop is to be installed must be sealed.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

Grounded electrical supply is required. See “Electrical Requirements” section. Proper gas supply connection must be available. See “Gas Supply Requirements” section.

The cooktop is designed to hang from the countertop by its side or rear flanges.

The gas and electric supply should be located as shown in “Gas and Electric Connection Locations” section so that they are accessible without requiring removal of the cooktop.

Provide cutout in left rear corner of cutout enclosure as shown to provide clearance for gas inlet, power supply cord, and to allow the rating label to be visible.

IMPORTANT: To avoid damage, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

Mobile Home - Additional Installation Requirements

The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes.

In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

4

Image 4
Contents Installation Instructions GAS Cooktop48 121,9 CM Modèle Commercial 9759405CTable of Contents Table DES Matières Cooktop Safety Your safety and the safety of others are very importantToolsand Parts Installation RequirementsLocation Requirements Product Dimensions Side View of CooktopCabinet Requirements Gas and Electric Connection LocationsMin Size Model Island trim Backguard Electrical Requirements Gas Supply RequirementsType of Gas Natural GasGas Supply Pressure Testing Gas Supply LineGas Pressure Regulator Burner Input RequirementsInstallCooktop Make Gas ConnectionTypical flexible connection Install GrillComplete Connection Install Griddle CompleteInstallation Adjust Flame HeightIf you need Assistance or Service Check Operation of Surface Burners, Grill and GriddleOn 36 91.4 cm models Wiring DiagramsSurface burners Surface burners with grill Surface burners with griddle On 48 121.9 cm modelsSurface burners with grill and griddle Sécurité DE LA Table DE Cuisson Votre sécurité et celle des autres est très importanteExigencesdemplacement Exigences DinstallationOutillageetpièces Dimensions du produit Vue latérale de la table de cuissonEmplacements des raccordements au gaz et à lélectricité Placards Dimensions à respecterMin Dimension Modéle Garniture Dosseret En îlotSpécifications électriques Spécifications delalimentation en gazType de gaz Gaz naturelCanalisation de gaz DétendeurCaractéristiques dalimentation du brûleur Test de pressurisation de la canalisation de gazInstallation delatabledecuisson Installation dun dosseret ou garniture en îlotRaccordementau gaz DosseretRaccordement typique par raccord flexible Installation du grilCompléter le raccordement Réinstaller la grille du gril Installation dela plaqueà frire AcheverlinstallationRéglage de la taille des flammes Si vous avez besoin dassistance ou de serviceSi le brûleur ne sallume pas correctement Schémas DE Câblage Sur les modèles de 36 91,4 cmSur les modèles de 48 121,9 cm 9759405C All rights reserved

9759405C specifications

The KitchenAid 9759405C is a versatile kitchen appliance that stands out for its robust features and innovative technologies, designed to enhance the culinary experience for home cooks and professional chefs alike. This appliance is part of a trusted brand known for quality and durability in kitchen products.

One of the main features of the 9759405C is its powerful motor, which provides consistent performance for various mixing tasks. Whether you are kneading dough for bread, whipping cream, or mixing batter for cakes, the strength of this motor can handle dense mixtures with ease. The appliance offers multiple speed settings, allowing users to select the ideal speed for their specific recipe. The versatility of speed options also ensures precision, whether you need a gentle fold or a vigorous mix.

Another standout characteristic of the KitchenAid 9759405C is its innovative planetary mixing action. This technology ensures that the mixing attachment moves in one direction while the bowl rotates in the opposite direction. This design allows for thorough mixing, which means ingredients are evenly combined without leaving unmixed pockets. It significantly reduces the time required to achieve optimal consistency in mixtures.

Durability is a hallmark of the 9759405C, as it is built with high-quality materials designed to withstand frequent use. The robust design and sturdy construction ensure that this mixer can endure the rigors of daily cooking. Additionally, it comes equipped with a variety of attachments, including a flat beater, dough hook, and wire whip, providing users with everything they need to tackle a wide range of cooking tasks.

The appliance's user-friendly interface and ease of operation make it accessible to cooks of all skill levels. The tilt-head design allows for easy access to the mixing bowl and makes it simple to add ingredients during operation.

Furthermore, the KitchenAid 9759405C’s sleek, modern design fits well into various kitchen aesthetics, making it not only a functional tool but also an attractive addition to your kitchen countertop. Its thoughtful features, coupled with advanced technology, make the 9759405C an essential appliance for anyone looking to elevate their cooking game. Whether you are a beginner or a seasoned chef, this mixer can simplify your culinary tasks and help you create delicious dishes with ease.