KitchenAid 3181199 installation instructions IAl, Electrical connection, Ungrounded neutral, Panel

Electrical requirements

IMPORTANT:

Save Installation Instructions for electrical inspector’s use.

Eleclrlcal Shock Hazard

-Eleclrlcal ground Is requlred on Ihls appliance.

-Improper connectlon of the equlpmenl-grounding conductor can result In electrlcal shock.

. Check wlth a qualliled eleClrlClan It you are In doubt as 10 whether the appliance Is properly grounded.

-Do NoL use an exlenslon cord with this appliance. Such us4 may result In a flre, eleclrlcal shock or other personal Injury.

-Do Not have a fuse In Ihe neutral or oroundlna clrcult. A tuse In the neutral & grounilng clrcutl could result In electrlcal shock.

Failure to follow these lnslructlons could result In an eleclrlcal shock or other personal Injury.

IAl.

A Ihree-wire, single phase, 240.volt. 60.Hz, AC only electrical supply is required on a separate, 40.ampere circuit, lused on both sides of Ihe line. (A time-delay luse or circuit breaker is recommended.)The fuse size must not exceed Ihe circuit rating of Ihe appliance speulied on the serial/raling plale localed on Ihe bottom 01 the cooklop.

It is Ihe personal responsibility and obligalion of Ihe customer lo conlact a qualilied electrician to assure lhal rhe electrical installalion is adequate and in conformance wilh National Eleclrical Code, ANSVNFPA 70.lalesl edition’. and all local codes and ordinances.

IB.

THE COOKTOP MUST BE CONNECTED WITH COPPER WIRE ONLY.

E-.l

I1

Wire sizes and conneclions must conlorm lo the reauiremenls 01 Ihe Nalional Electrical Code. AN’SI/NFPA 70 - latest edition’, and all local codes and ordinances.

Copies 01 the standards listed may be obtained lrom:

*Natlonal Flre Protecllon Assoclatlon Batterymarch Park

Qulncy, Massachuselts 02269

I I

I1

The appliance should be connected directly lo the fused disconnect (or circuit breaker) throuah Ilexible. armored or n&-metallic sheatied. - copper cable. The ilexible, armored cable extending Irom the appliance should be connecled directly to Ihe junction box. Allow two or three leet of slack in the line so that the appliance can be moved if servicing is ever necessary.

A U.L.-listed conduit connector must be provided al each end 01 the power supply cable (at the appliance and at the junction box). Wire sizes (COPPER WIRE ONLY) and conneclions musl conform with the rating 01 the appliance (40 amperes).

Electrical connection

Electrlcal Shock Hazard

-ElectrIcal ground Is required on thls appliance.

-This appliance musl be connecled lo a grounded, permanent wlrlng System or a grounding connector should be connected lo the grounding tennlnal or wire lead on the appliance.

-Disconnect power to the junction box.

-Do Not connect 10 the eleclrical SUPPIV until appliance Is permanently groinded.

Failure to do so could resull In eleclrlcal

1 shock, serious Injury, or death.

This appliance is manufaclured with a Irame- connected, green or bare, grounding wire.

Connecl the appliance cable to Ihe junclion box throuah Ihe U.L.-listed conduit connector. Com$ele eleclrical connection accordmg lo local codes and ordinances.

Where local codes permit connecting the frame-grounding conductor to the neutral (white) junction box wire:

grounded neutral

Figure 1

1. Dlsconnecl the power supply.

2, Connecl the green (or bare) appliance cable wire with Ihe neutral wire in the junction box.

3.Connect the two black wires together; then connect the two red wires together.

(See Figure 1.)

Where local codes Do Not permit connecting the frame-grounding conductor to the neutral (white) junction box wire:

Cable ham cooklop

ungrounded neutral

Figure 2

1, Disconnect the power supply.

2.Connecl Ihe two black wires together; lhen connect the two red wires logether.

(See Figure 2.)

3.Connect the green or bare grounding wire

lrom the appliance cable to a grounded wire in the junclion box or to a grounded, copper, cold waler pipe.”

4.Do Not ground lo a gas supply plpe or hot water pipe. Do Not connecl IO eleclrtcal SUPPIY until appliance is permanently grounded

(See Figure 3 )

*‘Grounded. cold water pipe must have melal continuity lo electrical ground and not be inlerrupled by plaslic. rubber. or olher slecVical insulaling conneclors such as hoses. lillmgs. washers or gaskels (including waler meter or pump). Any eleclrical insulating connector should be jumped as shown with a length 01No:4 copper wire securely clamped 10bare metal at bo!h ends.

Bumpson gmundlng c,.mp mu., OD”“ClPIPS.

GRaJNDlNGCLAMP

MUSTSETIGHT

ON PIPE.

Figure 3

Panel 0