Manuals / NAD / Home Audio / Stereo Receiver

NAD T 743 owner manual Quickstart, Play A Dvd Movie, English

Models: T 743

1 32

Download 32 pages 4.71 Kb

Page 9

QUICKSTART

QUICKSTART

In case you simply cannot wait to experience the performance of your new NAD T 743 receiver, we provide the following “Quickstart” instructions to get you underway. The steps below connect your DVD player to the T 743’s DVD input; be sure to read “Input Setup”, below.

PLAY A DVD MOVIE

•Connect the T 743’s composite video or S-Video MONITOR OUT jack to your TV/monitor’s corresponding input. (Cables not supplied)

•Connect your DVD player’s composite video or S-Video output to the T 743’s corresponding DVD input. (S-Video cable not supplied)

•Connect the DVD player’s optical digital output to the T 743’s optical DIGITAL IN 1 input. (Optical cable not supplied).

•Connect your left and right front speakers to the T 743’s FRONT L and R outputs, being sure to connect red to red (“+”) and black to black (“-”), with care to avoid stray wires or strands crossing between terminals. (Connect center, surround, and surround-back speakers as well, if you like). If your system includes a powered subwoofer, connect the T 743’s AUDIO PRE-OUT SW1, 2 or both jacks to its line inputs.

•Press in the main power switch (black pushbutton) on the T 743’s rear panel (this puts the T 743 into STANDBY mode and illuminates an amber LED to indicate it is ready to receive remote commands), then use the HTR 2’s [ON] key to power up the receiver. Be sure the TV/monitor is powered up, with the correct input selected.

•Start playback of the DVD player. Press the HTR 2 remote’s [Amp] Device Selector key, and then its (red) DVD/numeric 1 key to select the DVD input. You should hear multichannel or stereo sound, and see an image on the TV/monitor. (If one or the other fails to appear, you may need to use the receiver’s on-screen menu system to check assignment of audio, video, and digital inputs; see “Setting Up the T 743”.)

Enjoy the movie or music, but be sure to set aside time to read this manual thoroughly, and to set up, calibrate, and configure your T 743 carefully and completely.

ENGLISH

9

Image 9

NAD T 743 owner manual Quickstart, Play A Dvd Movie, English

Contents

ENGLISH EXPLANATION OF GRAPHICAL SYMBOLS SAFETY INFORMATIONPRECAUTIONS INSTALLATIONMAINTENANCE ELECTRIC POWERDAMAGE REQUIRING SERVICE DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELFTABLE OF CONTENTS TABLE OF CONTENTSGETTING THE MOST FROM THE NAD T TABLE OF CONTENTSENGLISH CONNECTING AM ANTENNA UNPACKING AND SETUPWHAT’S IN THE BOX CHOOSING A LOCATIONE.A.R.S. AND DIGITAL SURROUND ABOUT THE TEASE OF USE INTEGRATIONABOUT THE HTR 2 SYSTEM REMOTE CONTROL UPGRADABILITYABOUT THE T QUICKSTART PLAY A DVD MOVIEENGLISH 8 SEARCH FRONT PANELFRONT PANEL Default AssignmentENGLISH Digital Input Jack7+12V TRIGGER IN/OUT REAR PANEL8COMPONENT VIDEO IN 1-2 OUT Connect the COMPONENT VIDEO IN 1, and 2 inputs to component-videooutputs from compatible source components, typically a DVD player and terrestrial or satellite HDTV tuner. Connect the T 743 COMPONENT VIDEO OUT to the component-videoinput of a compatible video monitor/TV. Be sure to observe consistency in connecting the Y/Cr/Cb jacks some source and TV components label these Y/ Pb/Pr to the corresponding sources/inputs do not rely purely on the colour-codingof the jacks, which may not always be consistent among brands. The routing of the component-videoinputs follows the S-Video/composite,but is default as COMPONENT VIDEO IN 1 is routed to the COMPONENT VIDEO OUT jacks when the DVD input is selected COMPONENT VIDEO IN 2 is selected when the SAT input is active the audio and digital inputs assigned to DVD, and SAT will be used see also, Input Setup” REAR PANELENGLISH SETTING UP THE T GETTING STARTEDDEALING WITH HUM AND NOISE INPUT SETTINGS INPUT SETUPDISPLAY THE OSD NAVIGATING THE OSD AND MAKING CHANGESSPEAKER SETTINGS SPEAKER SETUPLISTENING MODE Front L/RUSING AN SPL METER CHANNEL-BALANCETEST SETUPSETTING CHANNEL BALANCE SETTING SPEAKER DISTANCECREATING AND USING PRESETS CREATING PRESETSRECALLING PRESETS ADJUSTING THE VOLUME USING THE TSELECTING SOURCES MUTING THE SOUNDSETTING RADIO PRESETS TUNING STATIONSSELECTING RADIO PRESETS SELECTING THE RADIODTS DIGITAL SURROUND ABOUT DTS AND DOLBY DIGITAL SURROUND MODESDOLBY DIGITAL DOLBY PRO LOGICUSING THE T ABOUT THE T 743S LISTENING MODESStereo Downmix Dolby Pro Logic Dolby Pro Logic II PLIISELECTING LISTENING MODES DISPLAYING THE SIGNAL MODEUSING THE T ENGLISHUSING THE T ADJUSTING LISTENING MODESDolby Pro Logic II PLII Downmix Dolby Digital Enhanced-Stereo1 ST1ADJUSTING CHANNEL LEVELS “ON THE FLY” SURROUND SOUND CHANNEL CHARTTO ADJUST CHANNEL LEVELS ADJUSTING THE TONE CONTROLSSPECIFICATIONS USING THE HTR 2 REMOTE CONTROLCONTROLLING THE T LEARNING CODES FROM OTHER REMOTESMACRO COMMANDS COPY A COMMAND FROM ANOTHER KEYPUNCH-THROUGH RECORDING MACROSFACTORY RESET KEY-ILLUMINATIONTIMEOUTDELETE MODE LOADING CODE-LIBRARIESSUMMARY OF HTR 2 MODES TRIGGER SETUPASSIGNING THE TRIGGER OUTPUT USING THE HTR 2 REMOTE CONTROLPOSSIBLE SOLUTIONSS TROUBLESHOOTINGCONDITION POSSIBLE CAUSESSPECIFICATIONS AV SURROUND SOUND RECEIVERENGLISH 2003 NAD Electronics International permission of NAD Electronics InternationalT 743 Manual GB 10/03 China