Hotpoint CIA 641 C S, CIC 642 C Electrical connection, Fixing, Single-phase connection

Fixing

The appliance must be installed on a perfectly level supporting surface.

Any deformities caused by improper fixing could affect the features and operation of the hob.

The thickness of the supporting surface should be taken into account when choosing the length of the screws for the fixing hooks:

•30 mm thick: 23 mm screws

•40 mm thick: 13 mm screws Fix the hob as follows:

1. Use short flat-bottomed screws to fix the 4 alignment springs in the holes provided at the central point of each side of the hob.

2. Place the hob in the cavity, make sure it is in a central position and push down on the whole perimeter until the hob is stuck to the supporting surface.

3. For hobs with raised sides: After inserting the hob into its cavity, insert the 4 fixing hooks (each has its own pin) into the lower edges of the hob, using the long pointed screws to fix them in place, until the glass is stuck to the supporting surface.

!The screws for the alignment springs must remain accessible.

!In order to adhere to safety standards, the appliance must not come into contact with electrical parts once it has been installed.

!All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool.

Electrical connection

!The electrical connection for the hob and for any built- in oven must be carried out separately, both for safety purposes and to make extracting the oven easier.

Single-phase connection

The hob is equipped with a pre-connected electricity supply cable, which is designed for single-phase connection. Connect the wires in accordance with the instructions given in the following table and diagrams:

Voltage and	Electrical cable	Wire connection
mains frequency
220-240V 1+N ~		: yellow/green
		N: the two blue wires together
50 Hz
		L: brown and black together

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

•400V - 2+N ~ 50 Hz

•220-240V 3 ~ 50 Hz

• 400V 3 - N ~ 50 Hz
			GB
• 400V - 2+2N ~ 50 Hz
Separate the wires and connect them in accordance
with the instructions given in the following table and
diagrams:
Voltage and	Electrical cable	Wire connection
mains frequency
400V - 2+N ~		: yellow/green;
50 Hz
220-240V 3 ~		N: the two blue wires
50 Hz		together
400V 3-N ~		L1: black
		L2: brown
50 Hz
		: yellow/green;
400V - 2+2N ~		N1: blue
50 Hz		N2: blue
		L1: black
		L2: brown

Connecting the electricity supply cable to the mains If the appliance is being connected directly to the electricity mains an omnipolar switch must be installed with a minimum opening of 3 mm between contacts.

!The installer must ensure that the correct electrical connection has been made and that it is fully compliant with safety regulations.

Before connecting the appliance to the power supply, make sure that:

• The appliance is earthed and the plug is compliant with the law.

• The socket can withstand the maximum power of the appliance, which is indicated on the data plate located on the appliance itself.

• The voltage falls within the range of values indicated on the data plate.

• The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets.

!Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.

!The cable must not be bent or compressed.

!The cable must be checked regularly and replaced by authorised technicians only.

!The manufacturer declines any liability should these safety measures not be observed.

!Do not remove or replace the power supply cable for any reason. Its removal or replacement will void the warranty and the CE marking. INDESIT does not assume liability for accidents or damage arising from replacement/removal of the original power supply cable. Replacement can only be accepted when carried out by personnel authorised by INDESIT and using an original spare part.

4