Hotpoint CSX27C warranty Solid Stik Motitor Syskrn

Page 8

Solid Stik Motitor Syskrn (continued)

The Solid State Monitor System alerts you when something starts to go wrong.

If a diagnostic code appears on the display, something needs special attention. To get your attention, the display code flashes until you erase it. The first 6 flashes are accompanied by beeps.

If more than one coded function requires attention at the same time, the one with the highest priority will be displayed first.

Pressing the STATUS CHECK- RESET pad will evaluate all other coded functions. If the NORMAL display is lit during the displaying of a code, that function is operating properly.

Pressing the STATUS CHECK- RESET pad will erase three codes immediately—Pfi CZand CC.

The DE and FFcodes can only be erased by touching the STATUS CHECK-RESET pad after the condition that caused the code to flash has been corrected.

This flashing code tells you to check your frozen food. Has any of it started to thaw? A package may be holding the freezer compartment door open. Don’t open the door more often than absolutely necessary while this code is displayed. Touching the STATUS CHECK-RESET pad after the freezer compartment temperature has returned to normal will erase the code.

This flashing code tells you the power to the refrigerator has been interrupted for more than 2 seconds. Check the condition of food in both the fresh food and freezer compartments. Touch STATUS CHECK-RESET pad to erase code.

There is no fault with the refrigerator when PF code flashes.

This flashing code tells you to check the automatic icemaker. Ice clumps in the storage bin may have stalled the icemaker. Follow corrective measures described on page 13. If water supply to the icemaker is not connected or not turned on, make sure manual icemaker switch is in the OFF position (see page 11). Code stops flashing when problem is corrected or STATUS CHECK-RESET pad is touched.

This flashing code tells you something’s wrong with the defrost system—keep doors closed to retain cold and call for service. Code flashes until problem is corrected.

This flashing code tells you to check temperature controls and adjust them if necessary. (See directions on page 5.) Touch STATUS CHECK-RESET pad to erase code. If code reappears after 4 hours, call for service.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Conkn@ GE Answer CenterHelp us Help you Ene~y-saving tipsRead this book carefully Write down the model and serial numbersImtillation Reauiremenk-IMPORTANT Please read carefully Md W Mtiti bfm X Uk apeWn% ref- f-n f ~ ~ o- p ~ ~~~e~=p~~vef~=oUse of Etiemion Cords Refrigerator bcationClearances Water Supply to IcemakerSet Temperature Controls How to Test TemperaturesOperating Your Refrigerator Automatic Energy Saver SystemWhen your refrigerator Is first plugged Solid Sbte Monitor SystemIf the signal light on How to Set Door AlarmWhy the Red Warm Temperature Li@t Glows Solid Stik Motitor Syskrn Signal Li@@ Di~nostic Codes Countermaker Compartment IcemakerIce & Water Dispenser Ice & Chilled Water Dkpemer Automatic Icemaker and Ice & Water DispemerImportant Fac@ about Your Ice &Water Dispenser Water flows from the household supply through aWhen Dispensing Ice When Dispensing WaterTo Dispense Ice and Water Once Your Icemaker and Dispenser Are in OperationWater Filter Icemaker Accessory To Stop DispensingIf Ice Clumps Form Storage Bin To Replace Ice Cube Storage BinFood Sto~e SuMestiom For convenienceTips on freezing foods To save money in enemy and food coshTo remove shelves ShelvesRemovable Bins on Fresh Food Compartment Door Sto~e Dmwers Convertible Meat KeeperSealed and fresh Drawer Sealed Snack WnTo Remove Dmwers Behind Refr~eratir Cleani~-ImideCare and C1eatiW Li@t Bulb Replacement CondemerMen You Won Vacation Men You MoveQuestiom? Use This fioblem Solver Fresh Food Or Freezer CompartmentTempewture ~0 Warm Foods DRY OUTProblem Solver If You Need Service Warranty
Top Page Image Contents