Black & Decker CMD3400MBC manual Water Filter Replacement, Setting the Clock, Brewing Coffee

5.Place filter holder inside the water reservoir and insert it into the recess at the bottom right hand corner (E).

Note: Replace carbon filter every 60 brewing cycles or every 2 months after removing it from the sealed package.

(Call the 800 number on the front cover for replacements).

E - +

WATER FILTER REPLACEMENT:

1.Press latch on filter holder to open (see illustration C).

2.Dispose of old carbon filter.

3.Remove new carbon filter from packing material.

4.Place new carbon filter inside filter holder.

5.Close the filter holder tightly until it snaps into place (see illustration D).

6.Place filter holder inside the water reservoir and insert it into the recess at the bottom right hand corner (see illustration E).

Note: Replace carbon filter every 60 brewing cycles or every 2 months after removing it from the sealed package. (Call the 800 number on the front cover for replacements).

SETTING THE CLOCK:

10.Select the brew strength desired by pressing the Brew Strength button and selecting one of the 3 levels desired (J):

	•	Mild
	•	Regular
	•	Strong
	Note: The Brew Strength can be selected before or after
J	brewing begins.

11.Press the Power button and brewing begins. Note: To delay brewing see, Delayed Brewing section.

12.The unit will beep 3 times when the brewing cycle is complete.

				13. Once the brewing cycle is complete the word Fresh
6:00
				and the Fresh icon will appear on the digital
AM				display (K).
PROG		FRESH
K HR	-
		+	MIN

14. After 20 minutes the digital display will change

12:00

AM

PROG

	-
HR		+	MIN

1.Plug appliance into standard electrical outlet.

2.The digital clock display flashes 12:00 A.M. (F).

3.To change the time: Press HR button until the correct time appears on the display. Repeat with the Min button.

Tip: Holding the button down makes the hours and minutes

6:20

AM

NOT

PROGFRESH

		-
L	HR		+

MIN

to Not Fresh and the icon will also indicate the

same (L).

15. Keep carafe on the warming plate between

servings to preserve the temperature of the coffee

in the carafe.

F

change rapidly after a short delay; tapping changes the time in 1 minute increments.

16. Once coffee grounds have cooled, press brew basket compartment release

Note: If the unit is unplugged or power is interrupted even momentarily, the time will need to be reset.

BREWING COFFEE:

1.Plug cord into a standard electrical outlet.

2.Open water reservoir cover.

	button to open.
17.	Use basket handle to remove and discard used grounds and paper filter.
	Replace basket and close brew basket compartment.
18.	The coffee maker automatically shuts off after 2 hours.
19.	Unplug appliance when not in use.

-

+

G

3.Fill carafe with desired amount of cold tap water using the water markings on the carafe; pour into water reservoir (G).

Note: Do not exceed the 12-cup maximum level.

4.	Close water reservoir cover securely.
5.	Press brew basket compartment release button to open.
6. Place 8 to 12 cup basket style paper filter into the

SNEAK-A-CUP®INTERRUPT FEATURE

The Sneak-A-Cup®feature allows you to pour a cup of coffee from the carafe while the coffee is brewing. When the carafe is removed the brewing process is paused. Simply replace the carafe on the warming plate within 30 seconds and brewing resumes.

TEMPERATURE CONTROL FOR WARMING PLATE

This coffeemaker has a temperature selector gauge for the warming plate on the control panel.

-

H

removable brew basket (H).

7. Add desired amount of ground coffee.

8. Close brew basket compartment securely.

9. Place empty carafe on the warming plate.

	-		+
		-
HR				+

M

STRE 1. By pressing the left or right button you can decrease or increase the temperature of the warming plate (M).

MIN 2. The bar on the LCD gives a visual display of the amount of heat of the warming plate.

7

8