Nuvo T2 manual Audio Settings, Auto-ON

Page 16

Audio Settings

These selections are intended for AM, FM and XM stand-alone applications. They should be left at default settings for NuVo audio systems. These systems allow identical audio control on a per-zone basis.

Bass EQ: Bass output can be adjusted +12 dB or down to 12 dB. The default setting is flat. This feature is useful for stand-alone use with an amplifier that does not have bass EQ control. If you are using the T2 with a NuVo audio distribution system, or another system that allows for EQ control, you should leave the T2 set at 0 dB (flat), fig 14.

Treble EQ: Treble can be adjusted the same as bass. The level ranges from 12 dB to +12 dB and defaults at 0 dB. As with the bass setting, this should not be used unless there is no external EQ capability, fig. 15. Balance: Left and Right channel output can be adjusted if desired. As with the EQ adjustments, this feature should not be used when the T2 is used with an audio system that already has EQ and balance adjustment capability, fig. 16.

Output Level: The signal level from the T2 can be adjusted up or down to match the input gain characteristics of other audio equipment in the system. The default setting is 0 dB and the range is 6 dB to +12 dB, fig. 17.

Auto-ON

Enable/Disable: The T2 can be set to turn the tuner displays on automatically when power is applied. This is a good feature for stand-alone use. In the event of a power outage or anytime AC power is lost and restored, the T2 tuners will automatically turn back on with the last-used settings without having to use the ON/OFF button on the front panel.

This selection is not necessary when using the T2 with the NuVo Concerto system, because the built-in power management system between the T2 and Concerto will automatically turn on the tuners when the Power button is pressed on any of the Concerto's Display Pads.

Fig. 14

Tuner A

Bass EQ: Bass EQ +4 dB

FM STEREO•AM•WEATHER

Fig. 15

Tuner A

Treble EQ: Treble EQ +6 dB

FM STEREO•AM•WEATHER

Fig. 16

Tuner A

Balance:

L------x------R

FM STEREO•AM•WEATHER

Fig. 17

Tuner A

Output Level:

Output +3 dB

FM STEREO•AM•WEATHER

SELECT

PUSH TO

ENTER

SELECT

PUSH TO

ENTER

SELECT

PUSH TO

ENTER

SELECT

PUSH TO

ENTER

Page 15

Image 16
Contents Page English French NEC National Electrical Code Table of Contents IntroductionNV-T2DF Wiring Diagram NV-T2DX Package Contents NV-T2DFX Package ContentsFront Panel Back Panel NV-T2RC3 Remote Control Installing the NV-T2 Dual Tuner Using the Aux. Input IR Pass-ThruAM/FM Antenna Input XM Antenna Input Proper Location of the XM Antenna Subscribing to XM Satellite RadioInfo Menu Option TreeAdvanced AM/FM Settings Operating ModeNuVoNet Regional Setup AM/FM Use Only Fine-Tuning AM/FM Use OnlyAudio Settings Auto-ONNoise Blanking AUX InputRS232 Communication Currently loaded on the T2 XM Display ButtonIV. Stand-alone Front Panel Use of the T2 Signal Strength/Stereo Indicator Using the Memory FeatureSource Switching StereoIV. Using the T2 with the Concerto NuVoNet Setting Up the Tuner for NuVoNetMaking the Connection Operating the T2 with the Concerto Display PadConfig New ConfigNuVoNet Operating Mode StartPresets Regional SetupPreset Information BrightnessXM Presets Add BankRename Bank Erase BankAdvanced Config Advanced ConfigCustom Regional Setup Tuning ParametersHigh Cut Audio Output LevelLevel Categories Categories TabFM Freqs AM FreqsDownload Configuration Successful DownloadTroubleshooting For XM Subscription Issues call Xmradio FM Section AM SectionXM Section Audio Section GeneralNuVo Technologies Delhi Pike Cincinnati, Ohio 45238, USA