Hobart LX18 ML-104349 manual Maintenance, Deliming General, Deliming Models LX18, LX18C & LX18H

Page 23

MAINTENANCE

DELIMING — GENERAL

WARNING: DELIMING SOLUTION, RINSE AGENTS, OR ANY OTHER KIND OF ACID MUST NOT COME IN CONTACT WITH BLEACH OR RINSE SOLUTION CONTAINING BLEACH USED IN CHEMICAL SANITIZING MACHINES. MIXING MAY CAUSE HAZARDOUS GAS TO FORM. THIS ENTIRE PROCEDURE MUST BE FOLLOWED STEP-BY-STEP FOR SAFE AND SATISFACTORY RESULTS.

Delime the dishwasher on a regular basis as required. The regularity will depend on mineral content of the supply water. Deliming should be done when you can see clear signs of lime deposits (a white chalky substance) on the inside walls and on the wash arms. If you have a model LX40 dishwasher, it is equipped with an automatic delime cycle reminder. It is recommended that deliming be done when DELIME flashes.

Inspect the machine interior for lime deposits. If deliming is necessary, a deliming agent (such as Lime Away or LSR) should be used for best results.

Depending upon the model of your machine, carefully follow the appropriate procedure outlined below.

DELIMING — Models LX18, LX18C & LX18H

1.Remove standpipe assemblies from chemical containers and place them as close to the floor as possible. Place a catch pan under them.

2.Cycle the machine four times to clear the lines of chemicals.

3.Remove rack from machine.

4.Close door.

5.Proceed with step 5 only if your machine is programmed for Modified Fill and Dump. If your machine is programmed for True Fill and Dump, skip step 5 and proceed directly to step 6.

If the displayed temperature is 160°F or below (130°F for LX18C models), start a cycle and wait for the machine to drain and fill. Open the door slowly just after the wash pump starts.

If the displayed temperature is above 160°F (130°F on LX18C), start a cycle. Open the door slowly just after the wash pump starts.

6.Add deliming agent (carefully follow supplier's instructions). The sump holds approximately 3 gallons of water.

7.Close door. Machine will complete the wash/rinse cycle.

8.Inspect interior of machine for lime deposits. Repeat steps 4 through 8 if necessary.

9.Press ON. Run two cycles to purge the system of deliming agent. Press OFF.

10.Put standpipe assemblies back into the appropriate chemical containers (see page 8).

11.Press ON. Run four cycles to prime the chemical delivery pumps.

12.Press OFF.

CAUTION: Do not allow the deliming agent to remain in the machine longer than recommended by the deliming agent manufacturer.

– 23 –

Page 22 Page 24
Image 23
Page 22 Page 24
Contents UCT I O Table of Contents Model Description LX Series Dishwashers GeneralLeveling InstallationUnpacking LocationWater Supply Plumbing ConnectionsDrain LX40H Electrical Connection Electrical DataCover Plate Chemical Sanitizer Models LX18C, LX30C, and LX40C Only Detergent and Rinse AIDInstallation Diagram LX18, LX18C & LX18H Installation Diagram LX30, LX30C & LX30H Installation Diagram LX40C & LX40H Controls Models LX18, LX18C, LX18H, LX30, LX30C & LX30H Fig OperationBefore First USE Do this Display Shows Remarks Modified Fill and Dump WASH/RINSE Cycle Times Diagnostic MessagesModels LX18, LX18C & LX18H Modified Fill and DumpWASH/RINSE Cycle Times Models LX30, LX30C and LX30HOperating Models LX40H & LX40C Controls Models LX40H & LX40C FigReady Ready ModePriming Chemical Pumps Models LX40H & LX40C WASH/RINSE Cycle TimesCycle Wash Drain Dwell Rinse Operator ProgrammingParameter Display Shows Manager Programming Machine Must Be In Ready ModePreparation ALL Models RecommendedFunction Programmable Variables DOs and DON’Ts for Your NEW Hobart Warewasher Cleaning ALL Models Deliming Models LX18, LX18C & LX18H MaintenanceDeliming General Deliming Models LX30, LX30C & LX30H Lubrication Deliming Models LX40H and LX40CSymptom Possible Causes TroubleshootingDR1 PRBLM, FILL1 Service

LX18 ML-104349, LX30C ML-104353, LX40H ML-104356, LX40C ML-104355, LX18H ML-104351 specifications

Hobart, a well-known name in the food service industry, offers a variety of high-quality equipment designed to meet the demands of modern kitchens. Among their impressive lineup are the LX30 ML-104352, LX18C ML-104350, LX30H ML-104354, LX18H ML-104351, and LX40C ML-104355 dishwashers. Each model brings a unique set of features and technologies that cater to different operational needs.

The Hobart LX30 ML-104352 is a compact dishwasher ideal for smaller establishments. It boasts a user-friendly digital control panel that enhances operational efficiency. With its powerful wash system, it can handle up to 30 racks per hour, making it perfect for busy environments. The LX30 is designed with a built-in booster heater that ensures optimal sanitization while conserving energy.

Next in line is the LX18C ML-104350, which is specifically tailored for smaller businesses or lower volume applications. This model has a lower profile, making it easy to install in tight spaces. It offers a wash cycle that can process 18 racks per hour, equipped with a robust stainless steel construction that guarantees durability and ease of cleaning. The energy-efficient design aids in reducing operational costs.

For those looking for enhanced performance, the LX30H ML-104354 is an excellent choice. This high-capacity model can wash up to 30 racks per hour, similar to the LX30 but with upgraded features that include an advanced filtration system that minimizes debris and optimizes cleaning performance. Its ergonomic design allows for convenient operation, while the chemical dispensing system provides an added layer of efficiency.

The LX18H ML-104351 model targets establishments that require a lightweight yet efficient dishwasher. It offers flexibility in operation and can process 18 racks per hour. Its space-saving design keeps utility costs down while maintaining rigorous hygiene standards with its built-in high-efficiency wash arms that reach every nook and cranny of dishes.

Finally, the LX40C ML-104355 stands out as a powerful choice for larger operations. Capable of washing up to 40 racks per hour, it is designed for heavy-duty tasks. Cutting-edge technology ensures thorough cleaning and sanitation, while adjustable wash cycles cater to various types of dishware. This model is also equipped with a comprehensive diagnostic system that simplifies maintenance and troubleshooting.

In summary, Hobart's LX-series dishwashers combine advanced features, durability, and efficiency, making them suitable for a range of food service operations from small cafés to large restaurants. With their focus on performance and user-friendliness, Hobart continues to lead the way in commercial dishwashing solutions.
Top Page Image Contents