Frymaster MJCFEC, FMCFEC, KJ3FC, J65X, JCFX manual

Page 18

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1.8.6 Replacing Heat Mode Indicator Light – Operating Thermostat Controls

1.Disconnect the fryer from the electrical supply.

2.Loosen the setscrew securing the thermostat knob and remove the knob. Remove the screws from the upper left and right corners of the control panel. The control panel is hinged at the bottom and will swing open from the top.

3.Disconnect the 9-pin connector and remove the control panel from the fryer by disengaging its tabs from the hinge slots in the mounting frame.

4.Carefully press the light out from the back of the control panel. Disconnect one wire at a time and reconnect it to the replacement light until all wires are transferred.

5.Carefully press the light back into the control panel.

6.Reverse steps 1-3 to reassemble the fryer.

1.8.7 Replacing Power/Melt Cycle Switch – Operating Thermostat Controls

NOTE: The Power/Melt-Cycle Switch, P/N 807-1404, has been replaced with a new switch, P/N 807-3498. When ordering the new switch, order Kit 826-1792, which contains the new switch and wiring instructions. The new switch is wired differently than the old one. Ensure the new switch is wired properly before operating fryer. Consult P/N 819-5889 (MJCF, MJ45 Switch Replacement Instructions) for further detail.

1.Disconnect the fryer from the electrical supply.

2.Loosen the setscrew securing the thermostat knob and remove the knob. Remove the screws from the upper left and right corners of the control panel. The control panel is hinged at the bottom and will swing open from the top.

3.Disconnect the 9-pin connector and remove the control panel from the fryer by disengaging its tabs from the hinge slots in the mounting frame.

4.Using a flat-tipped screwdriver, disconnect the chrome bezel from the tabs on the switch and press the switch out from the front.

5.Carefully press the new switch back into the chrome bezel, ensuring the tabs on the switch engage the slots in the bezel.

6.Disconnect the wires from the old switch and reconnect to the new switch until all wires have been transferred (see note at the beginning of this procedure).

7.Reverse steps 1-3 to reassemble the fryer.

1-13

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Hour Service Hotline 1-800-551-8633 April Master Jet CF Series Atmospheric Gas FryersPage Computers FCC Master Jet CF Series Atmospheric Gas Fryers Table of Contents Functional Description Pilot Ignition SystemControl Options Thermostats and Temperature Probes Accessing Fryers for Servicing Checking Burner Manifold Gas Pressure CE Standards for Incoming Gas PressuresAdjusting Pilot Flame Cleaning Gas Valve Vent Tube Adjusting Burner Ceramic Target Spacing and AlignmentCalibrating Thermostat Control Replacing Fryer Components Replacing ComputerPage Replacing Temperature Probe Replacing High-Limit Thermostat Computer Controls Page Replacing Melt Cycle Timer Operating Thermostat Controls Disconnect union arrow to remove burner manifold assembly Replacing Burner Ceramic Targets Replacing Pilot Assembly or Thermopile Replacing Frypot Reverse steps 1-22 to reassemble the fryer No pilot flame Troubleshooting and Problem IsolationPilot/Ignition Failures Unreliable flameProblems Related to the GAS AND/OR Electrical Power Supplies Improper Burner Functioning Improper Temperature Control Computer-Related Problems See .8.8 for retrofit informationRecovery Time Filtration Problems Filter Magic Simplified Wiring Diagram Troubleshooting, Millivolt Frying Systems LeakageHigh-limit ROBERTSHAW-UNITROL 7000 System Check Troubleshooting Guides Initial Troubleshooting, Millivolt Frying SystemsFryer Initial Troubleshooting, 24VAC Frying Systems But the switch light isProbe Resistance Chart Problem Probable Cause Corrective ActionWiring Diagrams Mjcf Millivolt Wiring Diagram, Non-CEMjcf Millivolt Wiring Diagram, CE Main VALVE/COIL Generator ThermopileWiring Diagram MjcfeMjcfec 24V Wiring Diagram 12.4FAST-Ready Constant Pilot Filter Magic II Wiring Diagram Filter Pump MotorMaster JET CF Series Atmospheric GAS Fryers Parts List AccessoriesMaster JET CF Series Atmospheric GAS Fryers Parts List Burner Manifold Components For SingleNatural Gas, w/Thermopile use 810-0426 for pilot only Cabinetry Components Fryer CabinetryMaster JET CF Series Atmospheric GAS Fryers Parts List Filter Magic II & Spreader Cabinet Cabinetry Filter Magic & Spreader Cabinet Cabinetry Casters, Legs and Associated Hardware Component Shield, Filter Box Assemblies and Components Component Shield Assemblies No Interface BoardComponent Shield Assemblies With Interface Board Filter Box Assemblies Control Panel Assemblies and Related Components Control Panel Assemblies and Related Components Filtration System Components Filter Magic II Drain Manifold Components1.1 Filter Magic Drain Manifold Components Standard ComponentEuro-Look Drain Manifold Components See page 2-27 for Euro-Look Drain Valve AssembliesAssembly Crumb Screen Not Included Order Separately Filter Magic II Filter Pan Components Outer Pan ComponentsFilter Magic Filter Pan Components Inner Pan Components Assembly Crumb Screen Not Included Order Item #8 Below Oil Return Handle Components Units Built Prior To April Master JET CF Series Atmospheric GAS Fryers Parts List Oil Return Plumbing OIL Return Plumbing Filter Magic II TypicalFilter Pump and Motor Components Standard EURO-LOOK Component PART# Drain Valves and Related Components 106-3760 Valve, Drain Assembly Full Vat Euro-Look Drain Valves and Related Components-Round DrainsPower Shower Components Frypot, High-Limit and Probe Components Frypot, High-Limit and Probe Components Wiring Connectors, Pin Terminals and Power Cords Plan Wiring Diagram KJ3FC Fast-ReadyMaster JET CF Series Atmospheric GAS Fryers Appendix Computer Wiring 3 KFCComputer Wiring Diagram 4 KFCKscf Wiring Diagram w/ Float CE KFC-1 Harness Diagram Transformer/Filter Box Wiring for Fast Computer Parts List KJ3FC Variant KJ3FC Variant Parts List KJ3FC Variant Parts List This page Intentionally Left Blank Service Hotline

JCFX, J65X, J3F, KJ3FC, MJCF specifications

Frymaster, a leading manufacturer of commercial frying equipment, offers a range of fryers tailored to meet the demands of various food service operations. Among their notable products are the FMCFEC, MJCFEC, MJCF, JCFX, and FMCFE models. Each of these fryers is designed with cutting-edge technology, emphasizing efficiency, performance, and ease of use.

The FMCFEC model stands out for its advanced filtration system, which provides exceptional oil management. This feature helps extend the life of cooking oil, delivering consistent frying quality while reducing operational costs. The FMCFEC is equipped with a digital controller that simplifies temperature management, ensuring food is cooked to perfection every time.

The MJCFEC is another remarkable model in Frymaster's lineup, featuring a versatile design suited for quick-service and casual dining establishments. It boasts a compact footprint while still offering a large frying capacity, enabling operators to maximize their output in limited space. Additionally, the MJCFEC incorporates energy-efficient technology, resulting in lower utility bills and a reduced environmental impact.

The MJCF model is geared toward high-volume frying, utilizing a powerful heating system that ensures rapid oil recovery. This fryer's heavy-duty construction enhances durability, making it ideal for busy kitchens where reliability is paramount. The MJCF model also features a straightforward interface, allowing staff to operate it with minimal training.

The JCFX model is designed with flexibility in mind, allowing for customizable frying options. This fryer offers multiple frying baskets and a range of temperature settings, making it suitable for various menu items, from fries to seafood. Its user-friendly digital controls enhance operational efficiency, making it easier for kitchen staff to manage frying times and temperatures.

Lastly, the FMCFE model emphasizes energy savings and oil conservation without sacrificing performance. This fryer incorporates advanced technology to monitor oil quality and usage, allowing operators to optimize their frying processes. The FMCFE's design focuses on safety, with features that minimize the risk of burns and splatters in busy kitchen environments.

In summary, Frymaster’s FMCFEC, MJCFEC, MJCF, JCFX, and FMCFE models reflect the company's commitment to innovation and quality in commercial frying equipment. With their distinctive features, energy efficiency, and user-friendly designs, these fryers are well-suited for a variety of food service applications, providing operators with reliable performance and exceptional results.
Top Page Image Contents