Frymaster MJCFEC, FMCFEC, KJ3FC See .8.8 for retrofit information, Computer-Related Problems

Page 29

MASTER JET CF SERIES ATMOSPHERIC GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1.9.3 Improper Temperature Control (cont.)

MELT CYCLE PROBLEMS

NOTE: In early 1999, PC board melt cycle timers replaced melt-cycle timer motors in new fryers.

See Section 1.8.8 for retrofit information.

In fryers equipped with thermostat controls, the melt cycle is controlled by a mechanical timer or a PC board. Three components that that can fail are the melt-cycle timer, the melt-cycle timer microswitch or the control panel melt cycle On/Off switch. Isolate the defect and replace defective component.

In fryers equipped with computers, the problem may be with the computer itself, the temperature probe, or a malfunctioning heat relay on the interface board. Refer to the troubleshooting tables in this chapter.

FAILURE TO CONTROL AT SETPOINT

In fryers equipped with thermostat controls, the problem will be with the thermostat itself. Possible causes are that the thermostat is out of calibration, the knob or flexible shaft is loose on the thermostat shaft, a thermostat wire is disconnected or broken, or the thermostat is defective. Refer to Section 1.7 for instructions on calibrating the thermostat.

In fryers equipped with other types of controls, the problem may be with the temperature probe, the interface board, or the controller. Refer to the troubleshooting tables in this chapter.

1.9.4 Computer-Related Problems

Computer Magic III.5 Features

Sensitivity or "Stretch Time"

Sensitivity or stretch time is a programmable feature that increases the cook time countdown based on variations in the oil temperature from the setpoint.

The sensitivity for each product button has 10 settings (0 through 9). A "0" sensitivity setting will disable the feature (no change in cooking time), while a nine will provide the highest sensitivity or most change. The correct sensitivity for any product is based on the product, its density, the setpoint temperature, and the customer’s own requirements.

1-24

Image 29
Contents Master Jet CF Series Atmospheric Gas Fryers Hour Service Hotline 1-800-551-8633 AprilPage Computers FCC Master Jet CF Series Atmospheric Gas Fryers Table of Contents Pilot Ignition System Functional DescriptionControl Options Thermostats and Temperature Probes Accessing Fryers for Servicing CE Standards for Incoming Gas Pressures Checking Burner Manifold Gas PressureAdjusting Pilot Flame Adjusting Burner Ceramic Target Spacing and Alignment Cleaning Gas Valve Vent TubeCalibrating Thermostat Control Replacing Computer Replacing Fryer ComponentsPage Replacing Temperature Probe Replacing High-Limit Thermostat Computer Controls Page Replacing Melt Cycle Timer Operating Thermostat Controls Disconnect union arrow to remove burner manifold assembly Replacing Burner Ceramic Targets Replacing Pilot Assembly or Thermopile Replacing Frypot Reverse steps 1-22 to reassemble the fryer Pilot/Ignition Failures Troubleshooting and Problem IsolationNo pilot flame Unreliable flameProblems Related to the GAS AND/OR Electrical Power Supplies Improper Burner Functioning Improper Temperature Control See .8.8 for retrofit information Computer-Related ProblemsRecovery Time Filtration Problems Filter Magic Simplified Wiring Diagram Leakage Troubleshooting, Millivolt Frying SystemsHigh-limit ROBERTSHAW-UNITROL 7000 System Check Initial Troubleshooting, Millivolt Frying Systems Troubleshooting GuidesFryer But the switch light is Initial Troubleshooting, 24VAC Frying SystemsProblem Probable Cause Corrective Action Probe Resistance ChartMjcf Millivolt Wiring Diagram, Non-CE Wiring DiagramsMain VALVE/COIL Generator Thermopile Mjcf Millivolt Wiring Diagram, CEMjcfe Wiring Diagram12.4 Mjcfec 24V Wiring DiagramFAST-Ready Constant Pilot Filter Pump Motor Filter Magic II Wiring DiagramAccessories Master JET CF Series Atmospheric GAS Fryers Parts ListMaster JET CF Series Atmospheric GAS Fryers Parts List For Single Burner Manifold ComponentsNatural Gas, w/Thermopile use 810-0426 for pilot only Fryer Cabinetry Cabinetry ComponentsMaster JET CF Series Atmospheric GAS Fryers Parts List Filter Magic II & Spreader Cabinet Cabinetry Filter Magic & Spreader Cabinet Cabinetry Casters, Legs and Associated Hardware Component Shield Assemblies No Interface Board Component Shield, Filter Box Assemblies and ComponentsComponent Shield Assemblies With Interface Board Filter Box Assemblies Control Panel Assemblies and Related Components Control Panel Assemblies and Related Components Filter Magic II Drain Manifold Components Filtration System ComponentsStandard Component 1.1 Filter Magic Drain Manifold ComponentsSee page 2-27 for Euro-Look Drain Valve Assemblies Euro-Look Drain Manifold ComponentsFilter Magic II Filter Pan Components Outer Pan Components Assembly Crumb Screen Not Included Order SeparatelyFilter Magic Filter Pan Components Inner Pan Components Assembly Crumb Screen Not Included Order Item #8 Below Oil Return Handle Components Units Built Prior To April Master JET CF Series Atmospheric GAS Fryers Parts List OIL Return Plumbing Filter Magic II Typical Oil Return PlumbingFilter Pump and Motor Components Standard EURO-LOOK Component PART# Drain Valves and Related Components Euro-Look Drain Valves and Related Components-Round Drains 106-3760 Valve, Drain Assembly Full VatPower Shower Components Frypot, High-Limit and Probe Components Frypot, High-Limit and Probe Components Wiring Connectors, Pin Terminals and Power Cords KJ3FC Fast-Ready Plan Wiring DiagramMaster JET CF Series Atmospheric GAS Fryers Appendix 3 KFC Computer Wiring4 KFC Computer Wiring DiagramKscf Wiring Diagram w/ Float CE KFC-1 Harness Diagram Transformer/Filter Box Wiring for Fast Computer Parts List KJ3FC Variant KJ3FC Variant Parts List KJ3FC Variant Parts List This page Intentionally Left Blank Service Hotline

JCFX, J65X, J3F, KJ3FC, MJCF specifications

Frymaster, a leading manufacturer of commercial frying equipment, offers a range of fryers tailored to meet the demands of various food service operations. Among their notable products are the FMCFEC, MJCFEC, MJCF, JCFX, and FMCFE models. Each of these fryers is designed with cutting-edge technology, emphasizing efficiency, performance, and ease of use.

The FMCFEC model stands out for its advanced filtration system, which provides exceptional oil management. This feature helps extend the life of cooking oil, delivering consistent frying quality while reducing operational costs. The FMCFEC is equipped with a digital controller that simplifies temperature management, ensuring food is cooked to perfection every time.

The MJCFEC is another remarkable model in Frymaster's lineup, featuring a versatile design suited for quick-service and casual dining establishments. It boasts a compact footprint while still offering a large frying capacity, enabling operators to maximize their output in limited space. Additionally, the MJCFEC incorporates energy-efficient technology, resulting in lower utility bills and a reduced environmental impact.

The MJCF model is geared toward high-volume frying, utilizing a powerful heating system that ensures rapid oil recovery. This fryer's heavy-duty construction enhances durability, making it ideal for busy kitchens where reliability is paramount. The MJCF model also features a straightforward interface, allowing staff to operate it with minimal training.

The JCFX model is designed with flexibility in mind, allowing for customizable frying options. This fryer offers multiple frying baskets and a range of temperature settings, making it suitable for various menu items, from fries to seafood. Its user-friendly digital controls enhance operational efficiency, making it easier for kitchen staff to manage frying times and temperatures.

Lastly, the FMCFE model emphasizes energy savings and oil conservation without sacrificing performance. This fryer incorporates advanced technology to monitor oil quality and usage, allowing operators to optimize their frying processes. The FMCFE's design focuses on safety, with features that minimize the risk of burns and splatters in busy kitchen environments.

In summary, Frymaster’s FMCFEC, MJCFEC, MJCF, JCFX, and FMCFE models reflect the company's commitment to innovation and quality in commercial frying equipment. With their distinctive features, energy efficiency, and user-friendly designs, these fryers are well-suited for a variety of food service applications, providing operators with reliable performance and exceptional results.