Xantech MX88 Rear Panel Features and Connections, Source Component Input Connections

Page 12

Page: 12

Model MX88

Figure 3 – The Model MX88 Controller/Amplifier – Rear Panel Connections and Functions

MX88 REAR PANEL FEATURES AND CONNECTIONS:

16.Keypad Terminals (8). Each Zone has one RJ-45 jack for Keypad Interface. Each connector interfaces the following: Power (Enough for 1 Primary & up to 4 Secondary Keypads per Zone), RS-485 Data I/O, and IR Input.

17.Speaker Terminals (8). Plug-in 4-terminal screw type connectors for zones 1 thru 6, permit speaker wire sizes up to 12AWG.

18.Composite Video Output (8). RCA type connector sends zone selected, source video to the composite video input on a zone TV or modulator (applies to MX88v(i) only).

19.Status Out (8). Provides a control output of +12 VDC that turns on and off with the zone to drive voltage sensing relay modules and AC strips.

20.Control Out (8). Mono 3.5mm Mini Phone Jack provides a Control Output that goes high (+12 volts) when any Zone is first turned ON and goes low (0 volts) when the last Zone is turned OFF. [Tip=+VDC; Shield=GND]

21.Remote Amp Control Out (CO1 & CO2). Stereo 3.5mm Mini Phone Jack connects to CONTROL IN jack of Remote Amp PA435X or PA4100X. Provides STANDBY and MUTE Control of remote Amp from Zone 7 (CO1) and Zone 8 (CO2). [Tip = STANDBY Logic; Ring = MUTE Logic; Shield = GND]

22.Source Component Input Connections (8)

a)Source Audio Inputs. Gold-plated RCA Jacks for Stereo/Dolby Pro line level audio input from source components.

b)Source Video Inputs. Gold-plated RCA Jacks for composite video input from source components (Applies to MX88 only).

c)Sense Inputs. 3.5mm Stereo Mini Phone Jacks for use with the CSM1 MX88 Current Sense Module.

© 2011 Xantech Corporation

Page 11 Page 13
Image 12
Page 11 Page 13
Contents MX88 Not Expose this Appliance to Rain or Moisture Xantech LLC General Information Each MX88 package containsCompanion products available for the MX88 sold separately Important Notes System Block Diagram System OverviewModel MX88 CONTROLLER/AMPLIFIER Features Preamp level audio outputs for all eight zonesModel MX88 MX88 CONTROLLER/AMPLIFIER Panel and Feature Descriptions MX88 Front Panel Features and ConnectionsSystem Status Power-Up Mode Front PanelZone Status Active-Operational Mode MX88 Rear Panel Features and Connections Source Component Input ConnectionsSource Loop-Thru Connections User Replaceable Fuse AMP L 250 VACInstallation Operation OUT-OF-THE-BOX PRE-TESTOFF MX88 CONTROLLER/AMPLIFIER Physical LocationConnecting the MX88 CONTROLLER/AMPLIFIER Audio Connections Zone systemExpanded, 16-zone system Video Connections MX88vi Only Zone systemRS232 Ports 1 Ethernet jack MX88vi and MX88ai onlyModel MX88 Status Control OutCO1 and CO2 Zones 7 Connections AT the Zone LocationSingle Keypad CAT5 Connections Multiple Keypad ConnectionsSensor Enable Zone Expansion Connecting TWO MX88 ControllersZone Termination External IR Terminal BlockConnecting Keypads or TOUCH-PANELS Composite Video SETTING-UP the MX88 System Typical 8-Zone MX88 SystemTypical 16-Zone Expanded MX88 System Firmware and Programming Model MX88 QuickConfig Planning the SystemUniversal Dragon Types of Commands RS232 ControlPIN # Function DSR GND DTR Ascii String „INITIATING‟ and „TERMINATING‟ CharactersModel MX88 Commands AO+Queries ?z#PR+Volume Level 39 Steps Keypad Button ID MX88 Setting Level in dB+14 +12Left Speaker Right Speaker MX88 Setting Attenuation Balance LevelTroubleshooting Problem Probable Cause and Solution38Model MX88 Model MX88Page 40Model MX88 RS232 and Expansion PIN OUT Information Specifications Video MX88vi onlyIR Sensor GeneralModel MX88 Xantech LLC Model MX88
Top Page Image Contents