Xantech mrc88 installation instructions Installation & Connections

Page 20
Section 2: Installation & Connections

Page: 20

Model MRC88

Section 2: Installation & Connections

INSTALLATION

OPERATION: OUT-OF-THE-BOX PRE TEST (BASIC/ADVANCED/EXPANDED)

The MRC-88 is shipped to operate basic functions ‘Out-Of-The-Box’ without any programming. Simply by plugging in keypads via standard CAT-5 RJ45 terminated patch cable and powering the controller ‘on’, you can control Source Selection, Volume Up/Down and speaker Mute capabilities.

Completing the Out-Of-The-Box Pre-Test will verify that all sources and zone components are working properly to select and distribute audio and video prior to programming with Dragon Drop-IR™. This will ensure that the unit is indeed functioning correctly ‘prior’ to fixed installation and allow proper troubleshooting procedures if a problem is encountered. Instructions regarding full programming for specific components and features will follow.

Note: For ‘EXPANDED’ configuration, test both units individually as outlined below.

Note: For simplicity of test set-up, only one Source Component, one pair of speakers, and one TV/Video Monitor will be necessary.

For the pre-test, you will need the following:

ƒ8-RJ45 Terminated CAT5 cables. (Pre test cables prior to use – See INSTALLATION Caution below)

ƒ1-Audio/Video Source Component (i.e. VCR, DVD or other) [Will be used to test ALL Source Inputs]

ƒ1 Audio/Video RCA Harness (Capable of Audio Left/Right and Video)

ƒ1-Pair of speakers with Speaker Cable properly terminated into a 4 conductor WECO Plug [Will be used to test Speaker outputs]

ƒ1-TV or Video Monitor [Will be used to test ALL Video Outputs]

ƒ8-283M Blink Emitter

ƒAll 8 MRC-88 Keypads

ƒMRC-88 Controller/Amplifier

ƒPA435X Two-Zone Stereo Amplifier (or other)

ƒ2 Pair of Stereo RCA Phono cables (for PA435X)

ƒAC Cord

1.Connect MRC88 Controller/Amplifier as shown in Figure 13 to:

a)All MRC88 Keypads via CAT5 Cables

b)Pre Amp Out of Zones 7 and 8 to PA435X Zones 1 and 2 Audio Input

c)Audio/Video Source to SOURCE 1 Audio Left/Right and Video Input terminals

d)TV or Monitor to Video Out 1

e)Speakers to Speaker Output #1

f)All 8 IR emitters to IR Emitter Ports 1 thru 8 (rear connection Item #26)

g)AC Power for MRC88 Controller and Audio/Video Source Component

2.Press “Power On” button on the front of the MRC88 Controller/Amplifier (wait for front panel LED’s to stop flashing – should be less than 20 seconds).

3.Power ON the Zone 1 TV/monitor and select the appropriate input (on the TV or monitor).

4.Power ON the Source Component and press play.

5.Place the emitter from IR Emitter Port 1 near the front of the Source Components IR Sensor window.

6.Press “POWER” on the Zone 1 Keypad.

7.Select “SRC1” on the Zone 1 MRC88 Keypad.

a)If Source 1 is an Audio/Video component, the video content of the source connected to the Source 1 inputs should be seen on the zone 1 TV/monitor.

© 2003 Xantech Corporation

Page 19 Page 21
Image 20
Page 19 Page 21
Contents INSTALLATION INSTRUCTIONS MODEL MRC88 EIGHT ZONE - EIGHT SOURCEAUDIO/VIDEO CONTROLLER/AMPLIFIER SYSTEM NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE NO USER-SERVICEABLEPARTS INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL PageTABLE OF CONTENTS SECTION 1 GENERAL INFORMATION & FEATURESSECTION 2 INSTALLATION & CONNECTIONS SECTION 3 PRE-PROGRAMMINGTHE MRC88SECTION 4 PROGRAMMING THE CONTROLLER LEARNING IR COMMANDS CREATING PALETTE FILESCONFIGURING SOURCE ICONS ON MRC88 KEYPAD LCD PLACING COMMANDS ONTO THE VIRTUAL KEYPADSECTION 5 ADVANCED/EXPANDED PROGRAMMING SECTION SECTIONSECTION 7 TWEAKING THE SYSTEM 2003 Xantech Corporation Model MRC88Page Section 1 General Information & Features GENERAL INFORMATIONIMPORTANT NOTE A MRC88 System can be a single controller with keypads for up to Eight zones or two connected controllers and keypads for up to Sixteen zones. There are three different setup modes in the Dragon Drop-IRSoftware. The Basic mode allows quick setup and programming for an Eight zone system. It assumes all zones will use factory defaults and will behave exactly the same. The Advanced mode allows customization of system configuration for functions such as zone link, monitor lockout, unique IR programming by zone, etc. The Expanded mode allows programming of systems with more than Eight zones using linked MRC88 Controllers Figure 1 - System Block Diagram SYSTEM OVERVIEWCONTROLLER/AMPLIFIER FEATURES KEYPAD FEATURES MRC88 FRONT PANEL FEATURES AND CONNECTIONS System Status Power-UpMode1.Front Panel PROTECT ON OFFZone Status Active-OperationalMode MRC88 REAR PANEL FEATURES AND CONNECTIONS 22.Source Component Input Connections23.Source Loop-ThruConnections MRC88 KEYPAD FEATURE DESCRIPTIONS MRC88 KEYPAD - FRONT FEATURES 1.MRC88 KeypaddFast Red Blink = IR Sensor INPUT or Keypad OUTPUT MRC88 KEYPAD - REAR FEATURES AND CONNECTIONS Section 2 Installation & Connections INSTALLATIONof obstructions MRC88Keep perforations on top cover free EXPANDED Figure 7 - MRC88 Keypad mounting template Note Do not tighten screwsMRC88 KEYPAD REMOVAL CONNECTING THE MRC88 CONTROLLER/AMPLIFIER SOURCE RELATED CONNECTIONSAudio Connections BASIC/ADVANCED Video Connections BASIC/ADVANCEDCSM1 Threshold Adjustments ADVANCEDBASIC/ADVANCED EXPANDEDEXPANDED ZONE RELATED WIRING CONNECTIONSBASIC/ADVANCED/EXPANDED RJ45 Connector at Controller/AmplifierCat 5 Cable BASIC/ADVANCED/EXPANDED Composite VideoControl Out BASIC/ADVANCED CO1 AND CO2 ZONES 7 & BASIC/ADVANCED/EXPANDEDZONE IR BASIC/ADVANCED/EXPANDED EXPANDEDKEYPAD CONNECTIONS AND JUMPER SETTINGS Single Keypad CAT5 ConnectionsMultiple Keypad Connections Table 1 - MRC88 Keypad Address Settings Sensor EnableApplication Zone TerminationCONNECTING SOURCE COMPONENTS LINKING TWO MRC88 CONTROLLER/AMPLIFIER UNITSMRC88 Connecting Block located on rear of Keypad Figure 11 - MRC88 Keypad CAT5 Cable Lengths1.Zones with IR Receiver ONLY BASIC/ADVANCED/EXPANDEDBASIC/ADVANCED/EXPANDED Composite Video Modulated VideoSETTING-UPTHE MRC88 SYSTEM Figure 13 -TypicalMRC88 SystemBASIC/ADVANCED EXPANDEDSection 3 Pre-Programmingthe MRC88 PLANNING THE SYSTEM BASIC MODEADVANCED MODE EXPANDED MODESOFTWARE INSTALLATION Windows 98/ME/NT/2000/XP INCLUDED HARDWARE & SOFTWARE ITEMSSTARTING MRC88 DRAGON DROP-IRSOFTWARE SERIAL PORT SELECTIONSTARTING A PROJECT BASIC/ADVANCED/EXPANDED LEARNING IR COMMANDS Creating Palette FilesBUILT-INIR CODE LIBRARY BASIC/ADVANCED/EXPANDED USING THE PALETTE EDITOR Figure Built-InMfg’s IR Command LibraryLEARNING IR COMMANDS BASIC/ADVANCED/EXPANDED Source BRAND selection in Palette Editor Source COMPONENT selection in Palette EditorCREATING A PALETTE FILE BASIC/ADVANCED/EXPANDED To Rename an Existing FunctionTo Add a New Function GETTING SOURCE COMMANDS FROM THE INTERNET Figure 19 Creating a Palette FileEDITING BRAND, COMPONENT, AND FUNCTION LISTS Importing CCF FilesImporting Discrete IR Hex Codes ENTERING RS232 COMMAND STRINGS Figure 20 Importing Discrete IR CodesADVANCED/EXPANDED USING THE RS232 PALETTE EDITORUsing PC TEST Using MRC88 TESTRS232 Palette Editor Window Entering RS232 Command StringsCREATING AN RS232 PALETTE FILE ADVANCED/EXPANDED Figure 23 Creating an RS232 Palette FileBASIC/ADVANCED/EXPANDED CONFIGURING SOURCE ICONS ON MRC88 KEYPAD LCDSection 4 Programming The Controller Figure 24 - MRC88 Keypad LCD Icon Generator CREATING NEW ICONSSELECTING ICONS FROM THE ICON GENERATOR DOWNLOADING SOURCE ICONS TO THE KEYPADPLACING COMMANDS ONTO THE VIRTUAL KEYPAD PLACING COMMANDS ON THE VIRTUAL KEYPADSELECTING IR PALETTES BASIC/ADVANCED/EXPANDED BASIC5.Repeat for all buttons / all sources ADVANCED/EXPANDEDPUSH & HOLD TIERED COMMANDS Figure Button Edit Pop-UpMenuEDITING BUTTONS ON THE VIRTUAL KEYPAD EDITING COMMANDS IN THE MACRO COMMAND LIST WINDOW BASIC/ADVANCED/EXPANDEDBASIC/ADVANCED/EXPANDED BASIC/ADVANCED/EXPANDEDADVANCED/EXPANDED Zone 1 thruFigure 27 Editing Commands PROGRAMMING POWER MANAGEMENT BASIC/ADVANCED/EXPANDEDADVANCED/EXPANDED BASIC8.Repeat for all components necessary PROGRAMMING SENSE TRIGGER CODES ADVANCED/EXPANDED 8.Repeat for all trigger inputs desired ZONE OPTIONS CONFIGURATION Default settings set in BASIC Mode are as followsNAME OF ZONE ADVANCED/EXPANDED RC68 CODE GROUPPRE AMP VOLUME ADJUST SETTINGS ADVANCED/EXPANDED IR LOOP BACK SETTINGS ADVANCED/EXPANDEDBASIC ADVANCED/EXPANDEDBASIC TRANSFERRING THE PROJECTFigure 32 Configuring Commands for IR IN ZONE ZONE AUDIO INPUT Section 5 Advanced/Expanded ProgrammingCONTROLLER OPTIONS PROGRAMMING IR ROUTING BACK-LIGHTCONTROLMODE OF OPERATION EXPANDED OPTIONSRS232 SETTINGS MONITOR LOCKOUT MODE Factory default “DISABLED”Factory default “DISABLED” ZONE LINKING PROGRAMMING Figure 37 - Dynamic Zone Link Programming Zones 1,2,3 & 4 programmed for Dynamic LinkingRS232 INPUT TRANSLATOR LINK ALL DYNAMICLINK ALL STATIC CLEAR ALLPROGRAMMING IR COMMANDS AND SEQUENCES Figure 39 - RC68 IR Command Macro Window RC68+ IR CODE TRIGGERED SEQUENCERPROGRAMMING INTERNAL AMPLIFIER COMMANDS Figure 41 - Using Internal Amplifier Commands Table 2 - Internal Amplifier Commands PROGRAMMING IN EXPANDED MODE ENABLING EXPANDED MODEPHYSICAL CONNECTIONS IN EXPANDED MODE RS232 CONTROL WHILE IN EXPANDED MODEFigure 42 Expanded Controller Connections Sources 1 throughPrimary MRC88 Controller/Amplifier From A/V loopthroughs on Primary ControllerSection 6 Completing the Programming Process TRANSFERRING A PROJECT TO THE MRC88UPLOADING MRC88 PROJECTS BASIC/ADVANCEDSAVING AND BACKING-UPFILES USING BACKUP FILESAUTOMATIC SAVE SAVE PROJECT ASFIRMWARE UPGRADE OPTIONIS WARM FIRMWARE UPGRADECOLD FIRMWARE UPGRADE DOWNLOADING FIRMWARE FILES FROM THE WEBSection 7 Tweaking the System ADVANCED/EXPANDEDMAKING FINE ADJUSTMENTS TRIMMING SOURCE AUDIO INPUT LEVELSZONE ADJUSTMENTS KEYPAD ADJUSTMENTSPOWERING THE ZONE ON AND OFF SETTING THE VOLUMEACCESSING TIER 2 COMMANDS Section 8 Operating InstructionsZONE SETTINGS AUDIO ADJUSTMENTS BASIC/ADVANCED/EXPANDEDSYSTEM STATUS BASIC/ADVANCED DYNAMIC ZONE LINK ADVANCED2.Press the button for the zone to be unlinked. Z1, Z2, etc The keypad status LED’s will show ‘busy’ rapid amber flash for 10 seconds after the last button press, then ‘time out’ and return to normal use mode LED /green, LCD/normal display. The small ‘L’ will no longer appear. The zones will resume independent control EXPANDEDTYPES OF COMMANDS Table 2 Rear Com Port Connector Pin OutSection 9 Appendix RS232 CONTROL?5SS3+ 7PR1+?5SS+ COMMANDS COMMANDNAME EXAMPLES/COMMENTSQUERIES NAMEQUERY RESPONSEVOLUME LEVEL 39 Steps KEYPAD BUTTON ID LEVEL in dB MRC88 SETTINGBASS/TREBLE LEVEL MRC88 Setting BALANCE LEVELLeft Speaker Right SpeakerPROBABLE CAUSE AND SOLUTION TROUBLESHOOTINGPROBLEM a Because of the wide variety of IR coding and PROBLEMPROBABLE CAUSE AND SOLUTION The following items may have interfered with the PROBLEMPROBABLE CAUSE AND SOLUTION PROBABLE CAUSE AND SOLUTION RS232 AND EXPANSION PIN OUT INFORMATIONPROBLEM Model MRC88 SPECIFICATIONS CERTIFICATIONSVideo IR Sensor2003 Xantech Corporation PageModel MRC88 Page Model MRC882003 Xantech Corporation XANTECH CORPORATION 12950 Bradley Avenue, Sylmar CAPage Model MRC88
Related manuals
Manual 102 pages 7.92 Kb Manual 12 pages 21.17 Kb
Top Page Image Contents