Installation Instructions, Prepare Location

Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

Vent piece	8" (20.3 cm) round
45° elbow	2.5 ft
	(0.8 m)

90° elbow	5.0 ft
	(1.5 m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example Vent System

90 elbow		Wall cap
	6 ft (1.8 m)	Wall cap
	6 ft (1.8 m)

2ft

(0.6 m)

The following example falls within the maximum vent length of 35 ft (10.7 m).

1	- 90° elbow	= 5.0 ft (1.5 m)
1	- wall cap	= 0.0 ft (0.0 m)
8 ft (2.4 m) straight		= 8.0 ft (2.4 m)

System length		= 13 ft (3.9 m)

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

■If the house has aluminum wiring, follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

■Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

INSTALLATION INSTRUCTIONS

Prepare Location

■It is recommended that the vent system be installed before the range hood is installed.

■Before making cutouts, make sure there is proper clearance within the ceiling for exhaust vent.

■Range hood is to be installed 24" (61.0 cm) min. for electric cooking surfaces or 27" (68.6 cm) min. for gas cooking surfaces to suggested maximum of 36" (91.2 cm) above the cooking surface.

■Check your ceiling height and the range hood height maximum before you select your hood.

1.Disconnect power.

2.Determine which venting method to use: roof, wall or non- vented.

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface.

W10274319E, W10272061 specifications

Jenn-Air, a brand recognized for its luxury kitchen appliances, continues to innovate with products designed for both functionality and aesthetic appeal. Among its offerings, the Jenn-Air W10274319E and W10272061 stand out. These two models are characterized by their commitment to quality, style, and advanced technology, ensuring an optimal cooking experience for all users.

The Jenn-Air W10274319E model showcases a sleek design that enhances any kitchen decor. One of its standout features is its powerful performance combined with energy efficiency. The appliance utilizes advanced temperature management technology, ensuring that your food cooks evenly and retains maximum flavor and moisture. This is further complemented by its intuitive controls, allowing users to easily adjust settings and monitor cooking progress.

On the other hand, the Jenn-Air W10272061 model also brings an impressive suite of features to the table. It incorporates smart technology that provides users with greater control and flexibility. Through Wi-Fi connectivity, users can access their appliance remotely, allowing for preheating, adjusting cook times, and receiving alerts right from their smartphones. This level of control not only enhances convenience but also helps in managing meal planning more effectively.

Both models are equipped with high-quality materials that not only look great but are also built to last. Stainless steel exteriors resist fingerprints and smudging, ensuring that your appliance maintains a clean appearance over time. Inside, both units offer spacious interiors with customizable configurations to accommodate various cooking styles and preferences.

Safety is another priority for Jenn-Air. Each model includes features such as automatic shut-off and child lock functions, ensuring peace of mind in a busy kitchen environment. These appliances also meet the highest industry standards for safety, providing users with an added layer of assurance.

In summary, the Jenn-Air W10274319E and W10272061 models reflect the brand's dedication to craftsmanship and innovation. With their blend of style, cutting-edge technologies, and practical features, these appliances are designed to elevate your culinary experiences while seamlessly integrating into your kitchen.