Installation, Installing Bottom Trim Piece

WARNING

Improper installation of the grounding circuit can result in a risk of electric shock.

Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, if doubt exists as whether the appliance is properly grounded.

CAUTION

For European style cabinets (flush front) the required clearance for operation of the oven door is minimum spacing of 7/8 between the cutout and the door, hinge or drawer of the cabinet.

Some built-in cabinets may not be wide enough, due to their construction, to allow this installation.

Installation

1.Cut hole in cabinet to mount oven. Cutout in cabinet should be level and straight.

NOTE: There are no provisions to level the unit after it is installed. An oven that is not level could cause poor baking results.

2.Install plywood floor as shown.

3.Remove oven door(s). See Oven Door Removal procedure.

4.Attach unit to the cabinet with four No. 8 x 1 screws supplied with unit inside of envelope containing these instructions. Pre-drill holes in cabinet for attachment screws using 1/8 drill. Oven mounting holes are provided in side trim.

5.Install bottom trim.

6.Replace oven door(s). See Oven Door Replacement procedure.

7.See instructions at right for electrical hook-up.

8.See Use and Care Manual for operating instructions.

Installing Bottom Trim Piece

Remove lower screws from hinge receptacle plates. Align lower trim and reinstall screws.

DO NOT INSTALL BOTTOM TRIM UNTIL UNIT IS ATTACHED TO THE CABINET.

Electrical Connections

Unit to be properly circuit protected and wired according to local electrical code and National Electrical Code.

It is advisable that the electrical wiring and hookup be accomplished by a competent electrician.

120/240 VAC or 120/208 VAC 60 Hz. See serial plate on front of unit for power requirements.

The neutral of this unit is grounded to the frame through the green or solid grounding wire. (The green and the white wires are twisted together at the termination of the conduit.) If used on new branch-circuit installations (1996 NEC), mobile homes, recreational vehicles, or in an area where local codes prohibit grounding through the neutral conductor, untwist or disconnect the green wire and connect the green wire to ground in accordance with local code. Connect the white neutral to the service neutral. Connect all wires to the branch circuit with approved connectors. Use copper or aluminum wire. If aluminum wire is used, use connectors recognized for joining aluminum to copper.

The chart below recommends the minimum circuit protection and wire size if the appliance is the only unit on the circuit.

K.W. RATING			RECOMMENDED MINIMUM	WIRE SIZE
K.W. RATING			CIRCUIT PROTECTION	WIRE SIZE
ON SERIAL PLATE			IN AMPERS	(AWG)
0	-	4.8	20	12
4.9	-	6.9	30	10
7.0	-	9.9	40	8
10.0	-	11.9	50	8
12.0	- 14.9		60	6

Service

Interrupt the source of electricity to the unit when attempting to repair or service the oven. Failure to do this could result in a dangerous or even fatal shock.

IMPORTANT - SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE

8101P485-60 specifications

The Jenn-Air 8101P485-60 is a sophisticated 48-inch built-in refrigerator that seamlessly combines elegance with advanced technology. This unit is designed not just for functionality but also to enhance the kitchen's aesthetic appeal, making it an ideal choice for modern homeowners who prioritize style and efficiency.

One of the most notable features of the Jenn-Air 8101P485-60 is its Dual Evaporator Cooling System. This technology ensures optimal humidity levels in both the refrigerator and freezer compartments, thereby preserving the freshness of food for a longer duration. By preventing the mixing of cold air between the two sections, it minimizes odor transfer, ensuring that flavors remain pure and distinct.

Another impressive characteristic of this model is its intuitive touchscreen control panel. This user-friendly interface allows homeowners to easily adjust settings, monitor temperatures, and control advanced features with just a few taps. Additionally, the panel features a customizable temperature setting for specific items, making it go-to for anyone who values precise temperature management.

The Jenn-Air 8101P485-60 incorporates a sleek stainless-steel finish that not only looks modern but is also resistant to fingerprints and smudges, ensuring that the refrigerator maintains its pristine appearance. Its integrated design allows for a seamless fit within cabinetry, creating a cohesive look in any high-end kitchen.

Energy efficiency is also a highlight of this model, as it meets or exceeds Energy Star qualifications. This not only supports sustainable living practices but can also lead to lower utility costs over time.

Storage is thoughtfully designed in the Jenn-Air 8101P485-60, with adjustable shelving, spacious drawers, and specialized bins for various food items. The organization options enable easy access and visibility, making it straightforward to locate ingredients.

Lastly, the refrigerator features a powerful water filtration system that delivers clean, great-tasting water and ice. The filtered water dispenser adds convenience for users who want immediate access to chilled water.

Overall, the Jenn-Air 8101P485-60 stands as an embodiment of luxury, innovation, and practicality, serving as not just a refrigerator, but also a centerpiece in any contemporary kitchen. Its features and technologies make meal preparation and food storage a breeze, truly elevating the cooking experience at home.