Conversion To LP Gas, Control Settings

Conversion To LP Gas

This appliance is shipped from the factory equipped for use with Natural Gas. To convert it from Natural Gas for use with LP Gas, perform steps 1 through 4.

1.Remove Natural Gas orifice hoods. Install color coded orifice hoods supplied. Located in a pack attached to the outer plenum area of this appliance.

(See Illustration “E”, below, and LP Gas Conversion instructions page 8).

2.Invert cap in convertible pressure regulator (if so equipped) located at entrance to gas manifold.

3.Adjust air shutters on individual burners for proper flame appearance.

4.Adjust low flame setting at each burner by turning adjustment screw in center of valve stem.

To make these conversions adjustments follow the instructions and illustrations (“A” through “E”, pages 5-7).

IMPORTANT

Apply a non-corrosive leak detection fluid to all joints and fittings in the gas connection between the supply line shut-off valve and the range. Include gas fitting and joints in the range if connections were disturbed during installation. Check for leaks! Bubbles appearing around fittings and connections will indicate a leak. If a leak appears, turn off supply line gas shut-off valve, tighten connections, turn on the supply line gas shut off valve, and retest for leaks. Never test for gas leaks with an open flame.

WARNING

Gas leaks may occur in your system and result in a dangerous situation. Gas leaks may not be detected by smell alone. Gas suppliers recommend you purchase and install a UL approved gas detector. Install and use in accondance with the manufacturer's instructions

This appliance is shipped from the factory with orifice hoods drilled for use with Natural Gas. To convert from Natural Gas to LP, apply a 1/2 open-end wrench to hex section of orifice hood. Turn counterclockwise to remove. Save the Natural Gas orifice hoods just removed from this appliance for future use. Install color coded orifice hoods supplied. (See LP Gas Conversion instructions above and page 8). Turn clockwise to install. Hold dimension specified in illustration “E”.

1/2 OPEN END

WRENCH

	11/16
	TURN
	CLOCKWISE
TURN	TO TIGHTEN
TURN
COUNTERCLOCKWISE	ORIFICE HOOD
TO REMOVE	ORIFICE HOOD

Illustration “E”

Control Settings

The size and type of cookware and the amount and type of food being cooked will influence the setting needed for best cooking results. The setting indicated should serve as a guide while you become familiar with your cooktop.

Use the HI flame setting to quickly bring foods to a boil or to begin a cooking operation. Then reduce to a lower setting to continue cooking. Never lease food unattended over a HI flame setting.

Med setting is used to continue a cooking operation. Food will not cook any faster when a HI flame setting is used than that needed to maintain a gentle boil. Remember, water boils at the same temperature whether boiling gently or vigorously.

Use LO setting to keep food at serving temperatures without further cooking You may find that some cooking may take place if the cookware is covered.

JGD8348CDP specifications

The Jenn-Air JGD8348CDP is a sophisticated gas cooktop designed for culinary enthusiasts who demand precision, style, and efficiency in their cooking spaces. With its sleek stainless steel finish and modern design, this cooktop not only enhances the aesthetic of any kitchen but also boasts a range of features aimed at delivering exceptional cooking performance.

One of the standout attributes of the Jenn-Air JGD8348CDP is its powerful burners. With five sealed burners, including a high-powered, 20,000 BTU Dual-Flame Burner, this cooktop excels in providing rapid heating and precise simmering capabilities. The dual-flame design allows for a broad range of heat settings, making it perfect for tasks ranging from quickly boiling water to gently melting chocolate without scorching.

The cooktop is equipped with advanced cooking technologies, including the Smart Heat technology that ensures even cooking temperatures across the surface. This feature minimizes hot spots and provides consistent results, thereby enhancing the overall cooking experience. Each burner is meticulously engineered for optimal performance, guaranteeing that home cooks can achieve restaurant-quality results.

Safety is another highlight of the Jenn-Air JGD8348CDP. The unit features an automatic re-ignition system that reignites the flame if it is accidentally blown out, providing peace of mind while cooking. Additionally, the cooktop includes a stainless steel griddle that offers a versatile cooking surface perfect for preparing pancakes, grilled sandwiches, and much more.

Cleaning up after cooking is made easy thanks to the seamless design of the cooktop. The porcelain-coated cast-iron grates are dishwasher safe, allowing for effortless maintenance. The smooth surface ensures that spills can be wiped away quickly, keeping the cooktop looking pristine.

Moreover, the knobs are thoughtfully designed, providing an intuitive interface for adjusting heat levels. With the addition of an integrated electronic ignition system, users can ignite the burners quickly and efficiently with just a turn of the knob.

In summary, the Jenn-Air JGD8348CDP gas cooktop is a premium choice for those looking to elevate their cooking experience. Its powerful burners, advanced technologies, and user-friendly features come together to create a stylish yet functional centerpiece for any kitchen. Whether you're a novice or an experienced chef, this cooktop offers the performance and precision needed to unleash culinary creativity.