Avanti IMP25, IMW24 Care and Maintenance, ? Cleaning Your Ice Maker, ? Space Requirements

Page 11

Operating Instructions

Starting your Ice maker

?Open the lid and fill the reservoir with water. Make sure the water level in the reservoir is not over the Ice collecting tray.

?Press START button to turn unit on.

?Select desired ice cube size by pressing “ice size” selectors S, M and L.

?Check the water level in the reservoir periodically. The ice maker will detect any shortage of water and stop operating. The ALERT indicator will be lit. Press the STOP button and fill the reservoir with water. W ait 3 minutes after the ALERTlight goes out and then press the START button. The Ice maker will begin operation.

?When the ice cubes are collected and reaches the bin sensor, the ice maker will stop operating and the ICE FULL indicator will be lit.

?There are three sizes of ice cubes available, therefore the larger the ice cube selected, the longer the time it will take to complete the cycle. When the ambient temperature is lower than

15°C (59ºF), the small or medium ice cubes sizes are recommended to avoid ice cubes clumping together.

?For best performance, water temperature should be between 7°C (45ºF) and 35°C (95ºF) and ambient between 15°C (59ºF) and 25°C (77ºF).

CARE AND MAINTENANCE

?Cleaning Your Ice Maker

?To ensure the cleanliness of the ice cubes, water in the reservoir should be replaced every 24 hours.

?If the compressor stops for any reason such as water shortage, too much Ice, power off, etc... Do not start the system right away, wait 3 minutes, and then re -start the Ice maker.

?Remove the drain plug to drain remaining water from the water reservoir when the ice maker will not be used for long period of time. Screw the drainplug back in place after the water has been drained.

?Always change with fresh water before starting ice production at initial installation or after long shut-off periods.

?Please clean your Ice maker regularly. When cleaning, unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean the inside and the outside surface of the Ice maker. Do not spray Ice maker with chemicals or diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.

Caution

Failure to unplug the ice maker could result in electrical shock or personal injury.

?Space Requirements

?During transportation, the incline angle of the cabinet should not be over 45°

?Do not turn the Ice maker upside down. Problems could occur in the compressor and sealed system.

?The Ice maker should be placed horizontally on a properly leveled surface.

?To ensure proper ventilation for your Ice maker allow 6” of space at the top, the back and on each side.

?Before using the Ice maker for the first time, please wait 2 hours after positioning it.

?Clean the inner liner, ice collecting tray, water box, ice shovel and evaporator frequently.

IMPORTANT: Do not install the Ice maker near an oven, radiator, or other heat source.

TEMPERATURE SENSOR

11

Image 11
Contents CE MAKER/MAQUINA DE Hacer Hielo Your Safety and the Safety of Others are Very Important ICE Maker SafetyImportant Safeguides Avanti Registration Form Registration Information? Protect Your Product ? Promote Better ProductsPage Help us help you… Arts and Features Table of contents ? Installation Of Your Ice Maker Important Safety InstructionsInstallation Instructions ? Before Using Your Ice MakerAlert Operating Your ICE MakerStop Select? Space Requirements Care and Maintenance? Cleaning Your Ice Maker ? Power Failure Problems with Your ICE MAKER?Troubleshooting Guide Problem Possible Cause Suggested SolutionsWarranty Fifth Year Warranty Your Avanti Products WarrantyWiring Diagram Instrucciones EN Español ? Antes de usar su máquina de hacer hielo Importante Instrucciones DE SeguridadInstrucciones DE Instalación ?CUIDADO?Alerta Alert Poniendo EN Funcionamiento SU Máquina DE Hacer HieloParar Stop Seleccionar Select? Necesidades de espacio Cuidado Y Mantenimiento? Limpiando su máquina de hacer hielo ? Fallas en la fuente eléctrica ¿PROBLEMAS CON SU Máquina DE Hacer HIELO?Guía DE Solución DE Problemas Problema Causa Probable Soluci ón sugerida

IMP25, IMW24 specifications

The Avanti IMW24 and IMP25 are part of Avanti’s innovative range of industrial microwave ovens, designed specifically to meet the demanding needs of commercial kitchens and food service operations. These units leverage advanced microwave technology to provide rapid cooking and reheating solutions without compromising on quality or taste.

The IMW24 is a compact yet powerful microwave oven that boasts a capacity of 24 liters. This model is equipped with a high-efficiency microwave generator that ensures quick cooking times, making it ideal for restaurants, cafes, and catering services. The intuitive control panel features multiple power settings and programmable options, enabling users to customize cooking parameters for a variety of dishes. The IMW24 also incorporates a stainless steel construction, ensuring durability and ease of cleaning, which is crucial in a fast-paced kitchen environment.

In contrast, the Avanti IMP25 offers an even larger capacity of 25 liters, catering to businesses with higher volume demands. This model integrates a more robust electric system, allowing for uniform heating and consistent results across multiple dishes. Like the IMW24, the IMP25 features user-friendly programmable settings and a digital display for precise monitoring. One of the standout features of the IMP25 is its inverter technology, which provides consistent heating while minimizing cold spots, thus enhancing food quality.

Both models come equipped with safety features such as door interlocks and automatic shut-off systems, ensuring safe operation even in bustling kitchen settings. The energy-efficient design of the IMW24 and IMP25 not only reduces operational costs but also supports sustainable practices in the food service industry.

The versatility of these microwave ovens allows them to handle various cooking tasks, from reheating leftovers to cooking multi-component meals. Their space-saving designs make them suitable for even the tightest kitchen setups, optimizing workflow without sacrificing performance.

In summary, the Avanti IMW24 and IMP25 are exemplary choices for commercial kitchens seeking reliable and efficient microwave solutions. With advanced technologies, durable construction, and user-friendly features, these models are engineered to improve productivity while maintaining high food quality standards. The investment in either of these appliances promises to deliver impressive results in any food preparation environment.