Bloomfield 9016, 9010, 9012 owner manual ELECTRICIAN’S Installation Instructions

Page 7

INSTALLATION INSTRUCTIONS (continued)

601 75815 Owners Manual Integrity Decanter Brewers

In some areas, local codes require a backflow preventer (check valve) to be installed on the inlet water line. If a backflow preventer is used, you must install a water hammer arrester in the incoming line, between the backflow preventer and the brewer inlet, as far away from the brewer as space will allow. This will relieve the excessive back pressures that can cause faucet leaks and solenoid malfunctions.

ELECTRICIAN’S INSTALLATION INSTRUCTIONS

REFER TO ELECTRICAL SPECIFICATIONS - Page 1 Check the nameplate to determine correct electrical service required for the brewer to be installed.

IMPORTANT: Before connecting to electricity, make sure automatic brewers are connected to the water supply.

Models 9010 & 9012 are equipped with a cord and plug. They require a 115 - 125 volt 20 amp circuit (50/60 Hz, 2 wire plus ground, with NEMA 5-15R or 5-20R Receptacle).

IMPORTANT: The ground prong of the plug is part of a system designed to protect you from electrical shock in the event of internal damage. Never cut off the ground prong nor twist a blade to fit an existing receptacle. Contact a licensed electrician to install the proper circuit and receptacle.

Models 9016 must be wired by an electrician, and require a 115/230V 20A circuit (50/60 Hz, 2 hot legs / 1 neutral leg, plus ground). Remove front panel to gain access to terminal block. Green terminal must be connected to a suitable building ground. Circuit must be capable of 3800 Watts. See figure 3 at right.

IMPORTANT: Wiring must be installed in approved solid or flexible conduit, and must be secured to the brewer with a strain relief (to be provided by the installer).

Models 9016EX must be wired by an electrician, and require a 220-240V 20A circuit (50/60 Hz, 2 hot legs plus ground). Remove front panel to gain access to terminal block. Green terminal must be connected to a suitable building ground. Circuit must be capable of 3800 Watts. Refer to 9016EX wiring diagram on page 23.

IMPORTANT: Wiring must be installed in accordance with local codes and ordinances.

NOTE: This equipment must be installed to comply with applicable federal, state and local plumbing codes and ordinances.

WARNING:

SHOCK HAZARD

Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury.

IMPORTANT: Do not connect brewer to electrical power until the tank is filled with water.

Pour water into the pour-over opening until water flows from the brew head.

IMPORTANT:

Supply power must match nameplate for voltage and phase. Connecting to the wrong voltage will damage the brewer or result in decreased performance. Such damage is not covered by warranty.

Fig. 3 115/240 Volt Terminal Block

5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Integrity Shipping Damage Claims Procedure Warranty StatementSpecifications Table of ContentsFeatures & Operating Controls Features and Operating ControlsAgency Approval Information Precautions and General InformationPLUMBER’S Installation Instructions Installation InstructionsLeveling the Unit ELECTRICIAN’S Installation Instructions Installation InstructionsSTART-UP OperationAutomatic Operation POUR-OVER FeatureHOT Water Faucet Preparation Brewing CoffeePOUR-OVER Operation Cleaning Instructions Procedure Clean Coffee BrewerSymptom Possible Cause Suggested Remedy Troubleshooting SuggestionsServicing Instructions Access PanelsTemp Temperature AdjustmentRemove Tank LID Assembly Timer AdjustmentReplace Thermostat Replace Heating Element Clean Solenoid ScreenReplace Solenoid Replace HOT Water Faucet Coil Replace Timer AssemblyRepair HOT Water Faucet Procedure Delime the Water Tank Servicing Instructions Description Used on HOT Water Tank AssemblyCabinet Plumbing Components Formed TUBE, Faucet Coil Inlet AssemblyALT Electrical Components126 Cabinet ComponentsModel Wiring DiagramsWiring Diagrams Genuin e Parts

9012, 9016, 9010 specifications

Bloomfield has made a significant mark in the world of precision machining with its innovative series of machines, particularly the Bloomfield 9010, 9012, and 9016 models. These machines embody the advanced engineering principles and cutting-edge technologies that Bloomfield is known for, making them ideal for a variety of applications across different industries.

The Bloomfield 9010 is a versatile platform known for its robust construction and high-speed capabilities. It features a powerful spindle motor that allows for increased torque and faster operational speeds, ensuring efficient machining processes. This machine is designed with user-friendly software that streamlines the programming and command procedures, making it accessible for operators of varying skill levels. Its enhanced cooling system contributes to improved precision by maintaining optimal temperatures during operation, ensuring that thermal expansion does not compromise work quality.

The Bloomfield 9012 extends the functional capabilities of its predecessor with additional features that cater to more complex machining tasks. It integrates advanced automation technologies that allow for seamless integration into existing production lines. The 9012 machine comes equipped with multi-axis machining capabilities, which enable it to perform intricate geometries with high accuracy. Furthermore, the machine's tooling system is designed to accommodate a wide range of cutting tools, enhancing its adaptability for different materials and specifications.

Lastly, the Bloomfield 9016 takes precision machining to the next level with its state-of-the-art features. This model boasts an intelligent feedback system that constantly monitors the machining process, making real-time adjustments to enhance precision and reduce waste. The 9016 is also designed with a modular architecture that allows users to customize the machine according to their specific needs, making it a flexible option for both small and large manufacturing operations. With advanced safety systems in place, operators can work confidently, knowing that the machine is designed to protect against potential mishaps.

In summary, the Bloomfield 9010, 9012, and 9016 models represent the pinnacle of precision machining technology. They are built for performance, versatility, and user convenience, making them suitable for a wide range of industrial applications. From high-speed operations to complex multi-axis machining, these machines are engineered to meet the evolving demands of modern manufacturing environments.
Top Page Image Contents