Bloomfield 8742 Solenoid Time Adjustment, Remove Tank Cover Assembly, Replace Thermostat

Page 15

SERVICING INSTRUCTIONS (continued)

606 Owners Manual for 8742-8748 Tea Brewer 76116

SOLENOID TIME ADJUSTMENT

The amount of water dispensed automatically during a brew cycle is controlled by the SOLENOID TIME section of the controller.

Place empty dispenser under brew chamber. Press the BREW switch. Including both brew water and dilution water, brewer should dispense:

A total of 3 gallons (Model 8742) of water; or, A total of 5 gallons (Model 8748) of water.

To adjust: Remove top panel.

Total delivered volume is dependant upon the total time the solenoid is energized. Adjust timer; clockwise increases time; counterclockwise decreases time. Run several cycles to check total amount of water delivered.

Adjust dilution. Turn needle valve all the way in (closed), then open 4-1/2 turns.

Brew several batches of tea to check for proper concentration and taste. Readjust needle valve and timer as required. Reinstall top panel.

REMOVE TANK COVER ASSEMBLY

Unplug brewer or turn circuit breaker OFF. Turn OFF water supply. Remove top panel.

Disconnect brew fill and outlet tubes from tank lid fittings.

Disconnect all wiring from thermostat, hi-limit and heating element.

Loosen center screw on tank hold-down bracket. Remove hold-down bracket by sliding short slotted end off of locking stud and lifting it off. Remove cover assembly by lifting it straight up. Reassemble in reverse order.

REPLACE THERMOSTAT

Unplug brewer or turn circuit breaker OFF. Turn OFF water supply. Remove top panel.

Disconnect all wiring from thermostat only. Loosen and free jam nut from pass-thru fitting securing temperature sensing bulb. Remove two screws holding thermostat to bracket.

Lift out thermostat, sensing bulb and thermostat gasket. Reassemble in reverse order.

IMPORTANT: Water pressure must be between 20 p.s.i and 90 p.s.i. flowing pressure.

If water pressure exceeds this value, or if water pressure varies greatly, a pressure regulator must be installed in the water supply line.

Fig. 11 Adjust Solenoid Time

IMPORTANT: Before setting assembly into tank, make sure tank lid gasket is properly seated on flange of lid.

IMPORTANT: When mounting thermostat, be sure a new seal washer is placed below the fitting on the capillary line. Push sensing bulb thru tank lid until fitting seats.

Tighten capillary lock nut only enough to ensure no water leakage. Excessive tightening is not necessary.

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 606 Warranty Statement Table of Contents SpecificationsApplicability Features and Operating Controls Agency Listing Information Precautions and General InformationInstallation PLUMBER’S Installation InstructionsLeveling the Unit ELECTRICIAN’S Installation Instructions InstallationSTART-UP OperationAutomatic Operation Water HeaterPreparation Brewing TEACleaning Instructions Procedure Clean Tea BrewerSymptom Possible Cause Suggested Remedy Troubleshooting SuggestionsAccess Panels TOP Panel Servicing InstructionsRear Panel Servicing Instructions Temperature AdjustmentSolenoid Time Adjustment Remove Tank Cover AssemblyReplace Thermostat Replace Solenoid Replace Timer AssemblyClean Strainer Screen Replace Heating ElementProcedure Delime the Water Tank 8742 8748 Exploded View & Parts List 8742 8748 Exploded View & Parts List 8742 8748 Service Kits 8742 8748 Wiring Diagram Telephone Fax

8742 specifications

Bloomfield 8742 is a cutting-edge platform designed to leverage the latest technologies in the field of data processing and management. This innovative system has been engineered to support a wide range of applications, making it a versatile solution for organizations seeking to enhance their data-driven decision-making capabilities.

One of the main features of Bloomfield 8742 is its robust architecture, which is capable of handling large volumes of data with impressive speed and efficiency. The platform employs distributed computing technology, allowing it to process data in parallel across numerous nodes. This not only accelerates processing times but also enhances the system’s scalability, enabling businesses to easily adjust their resources to meet growing demands.

Another standout characteristic of Bloomfield 8742 is its advanced data analytics capabilities. With built-in machine learning algorithms, users can extract valuable insights from their data without requiring extensive programming knowledge. The platform’s intuitive user interface simplifies the process of building and deploying models, fostering a more collaborative environment for data scientists and non-technical stakeholders alike.

Additionally, Bloomfield 8742 places a strong emphasis on data security. It incorporates state-of-the-art encryption protocols to ensure that sensitive information is protected at all times. Moreover, the system supports role-based access controls, enabling organizations to manage user permissions effectively and safeguard their data against unauthorized access.

The integration capabilities of Bloomfield 8742 are also noteworthy. It allows seamless connectivity with various external systems and applications, making it easy for organizations to enhance their existing workflows. Whether it’s connecting to an enterprise resource planning (ERP) system or integrating with cloud storage solutions, Bloomfield 8742 provides the tools necessary to create a cohesive data ecosystem.

In summary, Bloomfield 8742 stands out in the realm of data management solutions due to its powerful architecture, advanced analytics features, robust security measures, and seamless integration capabilities. As organizations increasingly rely on data to drive their strategies, Bloomfield 8742 proves to be an essential tool that meets the evolving needs of modern businesses, empowering them to turn data into actionable insights.
Top Page Image Contents